e AB has a width of 1.5 m and m. Determine the horizontale ical components of reaction

Q: Determine the centroid of the given composite figure. The area of the geometric figures drawn in red…

A:

Q: A wooden buoy (s.g. = 0.62) is 70 mm by 70 mm by 5 m long is made to float in sea water…

A:

Q: The blocks shown in the figure weighs 35 kips. Find the value of x

A: Thw weight of the block is balanced by buoyant force by oil and water.

Q: Question: A rectangular column is shown in the figure, assuming fc'=28Mpa, fy=345Mpa, and e=110mm,…

A: Eccentricity, Width of section, Depth,

Q: For the cross section shown, the distance of the plastic neutral axis from the bottom is * 8 in 2 in…

A: Given data in question  Dimensions of unsymetrical I sections To find out  Depth  of plastic neutral…

Q: y 53 mm 85 mm 25 mm 57° 25 mm - b 65 mm

A:

Q: Two cylindrical rods, one of steel and the other bronze are joined at C and restrained by rigid…

A:

Q: the surface area becomes 12.57 mm². By Using the following graphs, find the tensile strength and…

A: The given data is: Ao=Original surface area=20.25 mm2 A=Final surface area=12.57 mm2

Q: One piece is supported horizontally by 3 cables, as shown in the figure below. In the piece there is…

A: The center of mass of any body with hole can be calculated by determining the volume and centroid of…

Q: What is the weight (N) of a cube of stainless steel with 8 cm on each edge?

A: Each edge of cube is 8cm = 0.08m Volume of cube = 0.08x0.08x0.08 = 0.000512m3 The density of steel =…

Q: he platform scale consists of a combination of third and rst class levers so that the load on one…

A:

Q: Water Steel block 250 mm b. Mercury (s.g. = 13.6)

A: answer = 297.82 mm

Q: Problem 01: Given the figure at the right side: Determine the following a. Zx b. Sx c. shape factor…

A:

Q: PROBLEM 8: Locate the center of mass of the block in millimeters. Materials 1, 2 and 3 have…

A:

Q: Instructions: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with…

A: Use Dimensional Analysis & Chain conversion method. (Provide in Both) (In detail with each…

Q: Help Save & Exit S Archimedes, when asked by King Hiero if the new crown was pure gold (SG = 19.3),…

A:

Q: For the illustrated section: (7 inch, 5 inch, 2 inch) Determine: (a) the moment of inertia with…

A:

Q: The simply supported beam is built up from three boards by nailing them together as shown. The…

A: Given data - P = 14.9 KN Shear strength of each nail = 1.9 KN Find out - Determine the maximum…

Q: What is the nominal tensile strength of the member based on yielding a. 240 kN c. 150 kN b. 250 KN…

A:

Q: Give me right solution

A: Given data w=1.4 rad/s θ=35o cylinder weight=6lb From the figure cosθ=4rr=4 secθr=4sec 35or=4.8831…

Q: 8inch ↓ 12 inch ←

A:

Q: I am confused how we got 9 from this equation

A:

Q: Determine the volume V and total surface area A of the solid generated by revolving the area shown…

A: The given figure is as follows;To Find: Volume,(V) and total surface area(A) of the solid.

Q: 30 m 54 mm 48 mm 54 mm 72 mm A thin, homogeneous wire is bent to form the perimeter of the figure…

A: Wire is bent to form the perimeter of figure aboveCentre of gravity of wire with respect to x,y =?

Q: ood 0.56 m x 0.56 m x “h” meters in dimension was thrown into a liquid with SG = 2.078. It floats…

A: VOlume oftotal brickV=0.56×0.56×hVolume of brick inside SG=2.078V1=0.56×0.56×h-0.29Volume of brick…

Q: 5. What is the weight of each block shown below in pounds? Steel Block • 2'x2'x12' 49003 W = 490…

A: The given problem is based on definition of unit weight of a material. Also called as specific…

Q: A block of wood 0.25 m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.35…

A:

Q: 1-Calculate maximum axial stress in the cross section shown below in ksi, if M="see above". Please…

A: Axial Stress : Axial stress is the stress applied along a member or a body. The deformation of…

Q: an extension to a house has the appearance and dimensions in meters as shown in the drawing. zinc…

A: Solution:

Q: ALL SOLUTIONS

A:

Q: "hat does 'g' in psig mean?

A: To find : Meaning of p in psig.

Q: A block of wood 0.10m thick is floating in sea water. The Specific Gravity (SGw) of Wood is 0.85…

A:

Q: A spherical ball of copper having the original Surface area of 20. O0mm² and deformed until the…

A: Let us analyse the question in step 2.

Q: A Determine its smallest thickness b if its width is 56. Assume that it is fixed connected at its…

A: Given : Applied load = 600 lb L = 9.6 ft To Find : The smallest thickness b if its width is 5b.

Q: A block of wood 0.54 m x 0.54 m x "h" meters in dimension was thrown into a liquid with SG = 2.466.…

A:

Q: b. If the bar stretches 0.002 in., d naterial has lin ear-elastic behavi

A: WE KNOWMod of elasticity :E =StressAxial StrainAxial…

Q: Locate the centroid y of the cross section. Express your answer to three significant figures and…

A: Find out - 1) Centroid about Y axis .2) Moment of Inertia about the x' axis.

Q: about the x axis is: Y 6 4 2. 3.

A: Given data in question  Dimensions of shaded area in rectangular shape  Distances away from x axis…

Q: Before taking measurements, someone usually calibrates the measuring instrument. Describe your…

A: Calibration is the comparison of measurement results provided by a system under test with a…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.