A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What is the value of R? 2. What is the value of C? 1000 N 160 mm 200 N 400 N

Q: Angle of the resultant R (in degrees, measured counter-clockwise from the positive x-axis)

A:

Q: Replace the three forces and one couple which act on the bar by a force-couple system at the support…

A: Equilibrium of horizontal forces, ∑Fx=0Fx=5cos45°=3.54 kN Equilibrium of vertical forces,…

Q: urt B - Determine the forces in members BC, CH and AB Determine the force in member CH. nter your…

A:

Q: Determine the magnitude of the resultant force at A.

A: The given figure is shown below:

Q: 1. A steel shaft rotates at 8 Hz with 30 kW taken off at A, 20 kW removed at B, and 50 kW appli at…

A:

Q: Determine the forces in each members of 40 EN 3 m the truss loaded as shown. Tabulate the results…

A:

Q: Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed…

A:

Q: nto components along lines a-a’ and b-b’. 1. Determine the angle α knowing that the component along…

A: According to given data  300-lb force is to be resolved into components along lines a-a’ and b-b’.…

Q: F2 = 40 N 30° F1 = 30 N %3D

A:

Q: The resultant of the four belt tensions and a couple C = 450 N-m CCW and a force R = 700 Nacting…

A: Resultant force is given, which can be find out by summing up the horizontal forces to be equal to…

Q: The 10.5-kg uniform rod is pinned at end A. It is also subjected to a couple moment of 50 Nm. The…

A: Stiffness, k = 60 N/ m Mass of rod = 10.5 Kg

Q: Determine the reaction at the supports for the beam shown. The roller support B of the beam settles…

A:

Q: 2400 N 235° 25 960 N 960 N •6 @ 10.50 m 63 m a. Find the force in member AH. b. Find the force in…

A:

Q: The weight of the suspended object is W = 52 lb (Figure 1)

A:

Q: A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What…

A: Moment about OMO=1000(0.45)+200(0.3)-800(0.3)-400(0.45)Mo=C=90 N-m

Q: 90 mm 90 mm 60 tím 60 mm LUAI OSI

A: Given:- Moment=1600N-m To find:- P

Q: Determine the force system for equivalent at point A. Consider that each division represents 1 m, F1…

A: To find the resultant and moment about A-

Q: Find the force in spring if support A rotate 0.003 rad C.W and C settle 10mm E=200GPA and…

A:

Q: H. A machine operator produces the tension T in the control rod by applying the force P to the foot…

A:

Q: Q.8 In the design of a control mechanism, it is determined that rod AB transmits a 260 N force P to…

A: Given data, P = 260 N The force P is acting at a slope of  512 as given in the diagram. The angle…

Q: A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly…

A:

Q: Problem 2: Find the force in bar DB. (AE = constant.) 30k 7' D B 12' 12' 24'

A:

Q: Determine the change in length, breathand thickness f Ex a steel bar which is 4 m long jomm wide and…

A: It is required to determine the change in length of steel bar. δl=PLAE Here P is the applied load, L…

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: A rigid beam loaded with negligible mass is pinned at B and is supported by two indentical rods,…

A: Take Moment at B zero Deflection will be in ratio of distance from B

Q: 4.0m A 2358 Fixed Y 3.0m B Hingo at F Intorn 2.0m 25 KN To at 2.0m D and C D 10 KN/m E 3.0m 3.0m 15…

A: When a hinge is present, there is no restriction on rotation, and when another hinge is present, the…

Q: Please answer part C A = 150mm^2 E = 200GPa

A:

Q: Calculate the reaction force at joint H and joint A.

A: Moment at hinge is zero.

Q: From the given frame shown. Which of the following is the horizontal reaction at A? if q =18 kN, and…

A: Note :- The intensity of q will be in kN/m and is not in KN q=18 KN/m and L=5m

Q: ant of the force system in next fig. Then locate 1000 N.m 80 N 10m 150 N 100 N 10m A

A: Determine the resultant of the force system in next fig. Then locate it with respect to point (A).

Q: A 2 m 200 kN 2EI 3m 45 kN/m B El 5 m C

A:

Q: D 200 mm 300 mm -400 mm- A C When force P is applied to the rigid arm ABC, point B displaces…

A:

Q: The L-shaped body is supported by a roller at B and a frictionless pin at A. The body supports a…

A:

Q: Determine the reactions at the supports of the beam. Assume that support at B is a roller and EI is…

A: Some standard formula for slope and deflection.

Q: 50N Determine the following. a. Resultant moment at B b. Resultant moment at C 70N 80N 1m E

A: System of Collinear forces have been given and it has been asked to determine resultant  moment  at…

Q: Which of the following is the nearest value for the force at member CD? a. 4 kN compression b. 6…

A: Given Data  Find the force in member CD.