The horizontal shaft with a diameter of d = 44 mm is supported by a thrust collar that rests on a 37-mm-thick plate. The thrust collar is 29-mm thick. The thrust collar has an outer diameter of Dcollar =69 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar P Thrust collar Answer: d A = i Plate Determine the contact area between the shaft and the thrust collar. Thrust collar area mm² d Dcollar

The horizontal shaft with a diameter of d = 44 mm is supported by a thrust collar that rests on a 37-mm-thick plate. The thrust collar is 29-mm thick. The thrust collar has an outer diameter of Dcollar =69 mm. Determine the load P that causes an average shear stress of 69 MPa on the cylindrical surface of contact between the shaft and the thrust collar P Thrust collar Answer: d A = i Plate Determine the contact area between the shaft and the thrust collar. Thrust collar area mm² d Dcollar

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 7 kN and Q=5 kN. Determine the normal stress in the rod at x = 0.4 m. Assume a = 0.5 m and b=0.9 m. a Answer: σ= i B MPa O
3. A tube 2 mm thick has the shape shown in the figure Find the shearing stress caused by a torque of 600 N m. (Practice at Home) 10 mm - 80 mm 10 mm
The steel tube seen below has an outer diameter do = 60mm and an inner diameter d, = 50mm. It is subjected simultaneously to torque T = 1.5kN-m and to axial load P = 205kN. Determine: (a) the maximum in-plane shear stress and its orientation, (b) the associated normal stress and (c) sketch both on a properly oriented element.
All forces applied in the system are in the (x - y) plane. The material point B at the top of the beam is rotated at an angle of 15° counterclockwise. It is required that the shear stress is 17.5 MPa for this rotated material point B. At the bottom point A of the beam it is required that the maximum tensile stress is 110 MPa. Determine the load P and the length d that satisfies these constraints defined for points A and B. Given data: L= 4 b, t = b / 25, c = 2b, b = 1000 mm, e = 12, f=5 b/4- q = 2P/L b/ 4 -b/4- P
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
Several torques are applied to the stepped shaft (G= 80 GPa) shown in Fig. 1. Neglect any Stress concentrations associated with the sudden change in cross-section. Determine: (a) The maximum shear stress in the shaft (b) The rotation of the end E relative to the end A. 500 N-m 300 N-m FC 30 mm 400 mm A C 150 N-m 300 mm 350 mm D 50 N-m E 450 mm 20 mm
QUESTION 3) A horizontal beam AD is supported by an inclined strut CB and carries a load of 15 kN at joint D in the figure. The strut, which consist of two bars each of thickness 40 mm, is connected to the beam by a rivet passing through the three bars meeting at joint C. The allowable shear stress and bearing stress are t-60 MPa and o=120 MPa, respectively. a) Determine the required diameter of the rivet at the hinge C that carry safely by the given system. b) If the diameter rivet used on the support A is 20 mm check whether this rivet diameter is sufficient for the given system. 0.8m Im 0.6m 15 kN В Beam AD 20mm Strut CB 40mm 100mm 40mm 50mm 100mm Detail of joint C Detail of joint A
A steel bar 50 mm diameter and 1 m long just fits within a rigid hole carries a compressive load of 300 kN. Consider E= 200 GPa for steel and Poissons ratio υ = 1/4. Determine: (a.)Stress developed along lateral direction in MPa. (b.) Stress developed along lateral direction in MPa if the rigid hole has a diameter of 51 mm.
1.1
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tsquare/Tcircle of the shear stresses. Given: r = 11 mm, S = 18 mm, and t = 2.53 mm. S
a) 0.040 m b) 0.260 m c) 0.020 m d) 0.300 m