the heat to raise the temperature to the melting point the heat to raise the molten metal to the desired

Q: 1- The effective porosity is the value that is used in a gas reservoir engineering calculations.

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: ____________ part of cold chamber pressure die set up pushed the molten metal. a. Dies b.…

A: Die is special machine tool used in manufacturing to cut or form the material into a desired shape.…

Q: What improvements can be done to increase the efficiency to boil the water?

A:

Q: how do you solidify and cool in a metal casting process manufacturing

A:

Q: Mention the basic flame types a

A: Given: Basic Flame types

Q: 2. Discuss the basic operating principle of valve system in the ICE (provide drawing if necessary)

A: As per Bartleby's guidelines, we will post the answer of the first question, as there are multiple…

Q: how would you adjust the horizontal plane

A: The horizontal plane is a geometric plane that is perpendicular to the direction of gravity and…

Q: why bare pipe has 0% efficiency and full covered insulate pipe has more efficiency

A: A thermal insulator has a low thermal conductivity and is a poor heat conductor. To reduce heat loss…

Q: Draw the Ts diagram of the whole process

A:

Q: In which of the following casting process, the melting pot is an integral part of the machine. * O…

A:

Q: 32 - (CLO-1) What is cold shut defect? a) Two portions of metal flow together but there is lack of…

A: Cold shut is a casting defect

Q: machine design 1 question welding check the seam safety Example= Vd. ME Given data

A: For the given material specification, the yield and tensile stress.

Q: The explantion is not clear

A: given : height of channel h = 10m width of channel w= 34m angle made by channel θ= 15o to find:…

Q: Mold is manufactured in two parts top and bottom, size has to be smaller than the actual size of the…

A: As per given question  Mold is manufactured in two parts top and bottom, size has to be smaller than…

Q: The is a process in which heat is produced for welding by chemical reaction.* O Thermit welding O…

A: Welding processes are generally defined as a permanent metal joining process. Based on the type of…

Q: _is the temperature at which an oil substance gives off vapor continuously, when a flame is applied.…

A: TEMPERATURE  Temperature is the degree or intensity of heat contained in a substance or system, as…

Q: How would density be used to determine the concentration of antifreeze in the cooling system of an…

A: The density of antifreeze in the cooling system of automobiles is used to determine the…

Q: Please all solve the problem

A:

Q: Advantage and disadvantage of flame hardening

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: Why isnt the temprature used in this equation?

A: To state the reason for temperature in the equation

Q: Which one of the following material has the sheet metal applications O a. Mild steel O b. Cast iron…

A: Sheet metal is metal forming process which is used for forming into sheets

Q: What is the other name for the short column?

A:

Q: Define Constant Specific Heats (Approximate Analysis)

A: In constant specific heat assumption, the specific heat is assumed to be constant at some average…

Q: What is the maximum gas flow rate for a nozzle size?

A: GIVEN; What is the maximum gas flow rate for a nozzle size?

Q: A simple Rankine cycle uses water as the working fluid. Water enters the pump as a saturated liquid…

A: Since you have posted a question with multiple sub parts, we will provide the solution only for the…

Q: The wall thickness of a pipe is referred to as the pipe's __________.

A: Thickness of the pipe is nothing but the difference between outer radius and inner radius.

Q: Which hotspot on the lever below acts as the Effort?

A: This question is based on the concept of lever.

Q: 28. The metal is kept at the achieved temperature for some period of time. The time required depends…

A: Solution.jpg

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: False

A: It is False. Higher the gauge number, indicates thinner the sheet metal.

Q: The strength in the weld zone of an age-hardening aluminium alloy is often higher than in the heat…

A: particle that does not dissolve might transform into equilibrium phase instead , this is more likely…

Q: Mechanical working of metal is another name for O a. Casting process O b. Machining process O c.…

A: Mechanical working is forming process .. there are two types of working cold and hot working.

Q: Riser is designed so as to ?

A: Riser is part of gating system in casting process. The gating system includes pour basing, sprew,…

Q: Q14 Com Pare between the following 1-blast furnace alld cuPola furnace 2-Said alld Pressure die…

A: Difference between blast and cupola furnace: Blast Furnace Cupola The blast is like an…

Q: 61. Flashbacks are common in gas welding process if metal surface are not cleaned. Select one: True…

A: Flashbacks happens due to uneven metal surface in welding that build up a tip on the torch.

Q: hii, what's the right formula for n? h2 will be subtracted in the numerator too as well as in the…

A: ◆ The correct formula for efficiency of ideal Rankine cycle is given by, Efficiency = (Turbine work…

Q: What about the stretch for OA?

A: There is a mistake in the calculation part for TOA.   Consider the three equations (i), (ii), (iii)…

Q: 0/1 The weather has been hot. .many * weeks Since for to about

A: For is used in the sentence which talks about a period of time Example: for two hours for three…