Q6 Use the Iron carbon diagram to find 4 of the following. 1- The range of solidification temp. (start to end of solidification) for cast iron with 3% C. 2- The solid and liquid percent for Cast Iron with 2.7% C at 1320 °C. 3- Draw the expected microstructure at room temp. for hypo-eutectoid steel with 0.7%C. 4- Draw the expected cooling curve from the melting point to room temp. for cast iron with 4.3%C. 5- The steps and the allotropy change for steel with 0.01% C.

Q6 Use the Iron carbon diagram to find 4 of the following. 1- The range of solidification temp. (start to end of solidification) for cast iron with 3% C. 2- The solid and liquid percent for Cast Iron with 2.7% C at 1320 °C. 3- Draw the expected microstructure at room temp. for hypo-eutectoid steel with 0.7%C. 4- Draw the expected cooling curve from the melting point to room temp. for cast iron with 4.3%C. 5- The steps and the allotropy change for steel with 0.01% C.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4. .acta as a deoxidation of liquid steel 5.Iron-carbon steel at 1100c has. . stracture and called. 6.Interstitial spaces less than carbon diameter lead to ......
1. Given the time-temperature transformation diagram, what would be the phases present for a 1.13 wt. % C steel with no alloying elements. calculate the amount of pro eutectoid product, where applicable (at the bottom) A) quenched in cold water to 650 C in 0.1 seconds, then held at 650 C for 5 seconds, then quenched to 400 C, held at 400C for 60 seconds, and finally quenched to room temperature B. Necessary Steel Phase Diagram Calculations to determine the amount of pro eutectoid product:
3) You see Al-Cu phase diagram below and two microstructures (A and B) having the same nominal composition of 3 percent Cu. In these microstructures, matrix is a and spheres refer to CuAl₂ particles. In A and B, the size of big particles are the same. a) For the same volume constant, if we heat treat the both microstructures at T₁ for a long time, is there any changes in both microstructures? If so, what is that? And is the changes the same for both A and B? Is the rate of changes the same for A and B? Draw the final microstructures of A and B if any changes occur you think so. Temperature a AI 2 I 4 a +CuAl2 1 6 Copper,% CuAl2 α
12-70 A steel is heated until 40% austenite, with a carbon content of 0.5%, forms. Estimate the temperature and the overall carbon content of the steel.
In a melting point phase diagram what do you mean by the eutectic point? How does this affect the obtained melting point range?
Q.6 Discuss the following transformation in TTT diagram at eutectoid composition with their microstructure. i. Austenite to pearlite ii. Pearlite to spheroidite iii. Austenite to martensite iv. Martensite to martensite
the PCS containing 0.4%C was quenched hardened in water, amd tempered at 400oC. sketch and identify the phases of the microstructure pf the stell at rhe following states a) above the upper critical point just before quenching in water b) after quenching I’m water prior to tempering C) after tempering
Material science Assuming this system forms a laminar type eutectic, determine the volume proportion of phases for an equilibrium solidified 50% Pb alloy. Sketch the expected microstructure.
For some given binary phase diagram, describe how you would: find the temperatures and compositions of all eutectic, eutectoid, peritectic, and congruent phase transformations write reactions for all these transformations for either heating or cooling (show an example).
Q) A graph of your temperature versus time cooling curve. Discuss the indicators of solidification initiation and termination and the implied alloy composition(s) I have provided with the grpah of the tmep vs time cooling curve and the phase diagram please answer the above question accordingly in paragrahps
Consider the phase diagram below. The three points A, B, and C are at concentrations of 27, 31.9, and 33.8 wt% Ni respectively. The ends of the tie line are at C1 = 25% wt% Ni and C2 = 35 wt% Ni. What are the weight fractions of the alpha phase at A and the L phase at B, as well as the alpha phase/L phase ratio at C? T(°C) 1300-L (liquid) 1200 20 ABC L + a C1 30 S C2 liquidus 40 L + a solidus α (solid). O a. Walpha=0.12; WL=0.41; Walpha/WL = 9.41 O b. Walpha=0.27; WL-0.26; Walpha/WL = 11.11 O c. Walpha=0.15; WL-0.26; Walpha/WL = 11.80 Od. Walpha=0.20; WL-0.31; Walpha/WL = 7.33 50 wt% Ni
From the phase diagram of the Fe-0.25wt%C alloy below, determine the phase fraction and elemental composition of the resulting phase immediately after solidification across the eutectoid line (725 C). a.alpha_eutectoid = 96.6 wt% and cementite = 29.85 wt% b.alpha_eutectoid = 96.6 wt% and cementite = 3.4 wt% c.alpha_eutectoid = 1.05 wt% and cementite = 29.85 wt% d.alpha_eutectoid = 29.85 wt% and cementite = 1.05 wt%