Ans this question and Complete solution 12 kg of air per minute is delivered by a centrifugal air compressor. The inlet andoutlet conditions of air are: V1 = 12 “, P1 = 100 KPa , v1 = 0.5m3andkgm3V2 = 90 ", P2 = 800 KPa , v2 = 0.14. The increase in enthalpy of air passingkgKJand heat loss to the surroundings is 700kgthrough the compressor is 150KJmin

Answered: Image /qna-images/answer/1796beb4-4383-403f-b936-673dab9e43ab.jpg

12 kg of air per minute is delivered by a centrifugal air compressor. The inlet and m3 and kg outlet conditions of air are: V1 = 12 , P1 = 100 KPa , V1 = 0.5 - V2 = 90 ", P2 = 800 KPa , v2 = 0.14 . The increase in enthalpy of air passing kg through the compressor is 150 KJ and beat loss to the surroundings is 700 KJ

12 kg of air per minute is delivered by a centrifugal air compressor. The inlet and m3 and kg outlet conditions of air are: V1 = 12 , P1 = 100 KPa , V1 = 0.5 - V2 = 90 ", P2 = 800 KPa , v2 = 0.14 . The increase in enthalpy of air passing kg through the compressor is 150 KJ and beat loss to the surroundings is 700 KJ

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Could you please spreate each question alone because there are two questions
12
With complete and clear units/conversion factors. Box your final answer and round to the nearest 2 decimal places. Thank you
Please answer 3, 4, 5, 6, 8, 9, 10, 12 1 is 0, 2 is 0, 7 is point A, 11 is 2. I included a picture of someone who solved but they were mostly incorrect. Please do not answer if the solution set I provided with the incorrect answers was you. I appreciate the attempt, but the solutions for 3, 4, 5, 6, 8, 9, 10, 12 were marked wrong, so unless you have different answers, please do not submit the same incorrect solution set. The wheel is attached to the spring. The mass of the wheel is m=20 kg. The radius of the wheel is 0.6m. The radius of gyration kG=0.4 m. The spring’s unstretched length is L0=1.0 m. The stiffness coefficient of the spring is k=2.0 N/m. The wheel is released from rest at the state 1 when the angle between the spring and the vertical direction is θ=30°. The wheel rolls without slipping and passes the position at the state 2 when the angle is θ=0°. The spring’s length at the state 2 is L2=4 m. (1) If the mass center G is set as the origin (datum), the gravitational…
26. A JELLO IS sußJECTED TO %3D 0) DRAW THE DEFORMEO SHAPE CALCULATE ?
Can I have the formula for the percent difference?
Show all work and steps please
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
Solidworks
support it with the correct solution. 2. Which of the following is not an extensive property? A. lengthB. melting pointC. volumeD. weight
Write the formula for Macaulay Functions?
3) Graphically trace the area which contributes to the load for each joint of the middle parallel chord truss shown on the plan from a distributed area load. Also complete the free body diagram for the section shown for the truss on the bottom figure (with loads) with the appropriate directions (senses). 0.5P (3) 3 P