The hangers support the joist uniformly, so that it is assumed the 4 nails on each hanger carry an equal portion of the load. The joist, with total length L = 10 meters, is subjected to the trapezoidal loading shown where W1 = 12 kN/m, and W2 = 21 kN/m. Each nail of the hanger at end A and end B has a diameter of 11 cm and 14 cm, respectively. Determine the average shear stress (MPa) in each nail of the hanger at end B. Note: The hangers only support vertical loads. ROUND OFF TO TWO DECIMAL PLACES. W2 W1 A B L

The hangers support the joist uniformly, so that it is assumed the 4 nails on each hanger carry an equal portion of the load. The joist, with total length L = 10 meters, is subjected to the trapezoidal loading shown where W1 = 12 kN/m, and W2 = 21 kN/m. Each nail of the hanger at end A and end B has a diameter of 11 cm and 14 cm, respectively. Determine the average shear stress (MPa) in each nail of the hanger at end B. Note: The hangers only support vertical loads. ROUND OFF TO TWO DECIMAL PLACES. W2 W1 A B L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The question is in the picture. Thanks
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 3.6 in., d = 10.8 in., a = 3.2 in., and t = 0.4 in. For a vertical shear force of V = 39 kips, determine the shear flow through the welded surface at B
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
A timber frame or truss shown below supports a load P of 50 kN. Find (a) the normal stress in all the members, (b) the horizontal shearing stress at the notched ends of timber AC, and the bearing stress of C on plate D that measures 0.25 m x 0.25 m x 0.025 m. P = 50 KN B 0.17 m 30° 0.15 m 10 0.25 m 0.1 m につく 0.25 m
Can someone please answer this? Thank you, in advance.
Q2) For single story building shown in Figure below, all beams are 300x500 mm, all columns are 300x300 mm. The building subjected to dcad load 3 KN/m and the roof live load 8 KN/m 5 m 0.3 a. The slab thickness for deflection control. b. Check the shear adequacy of the slab. c. By using Ø 12 mm, what is the required 12 m positive reinforcement at section A-A?. d. If the top reinforcement at section B-B is Ø 12 mm @ 200 mm, show if this reinforcement is adequate to support the applied load? e. Find the maximum applied load on beam A &B 0.3 B 12 m 0.3 12e200 53m 5.30 m Good Luck 1 045
The pin support A and roller support B of the bridge truss are supported on the concrete abutments. If the square bearing plates at C and D are 20 inches x 20 inches, and the bearing failure for concrete is (?????)? =3.8 ???, determine the factor of safety against bearing failure for the concrete under each plate.
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 6.0 in., d=18.0 in, a = 3.3 in., and t= 0.8 in. For a vertical shear force of V = 45 kips, determine the shear flow through the welded surface at B
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 6.0 in., d = 18.0 in., a = 4.0 in., and t = 0.7 in. For a vertical shear force of V = 34 kips, determine the shear flow through the welded surface at B. d B a
For the beam showna. Determine the maximum flexural stressb. If the nails shown in the cross-section can each support a shear force of 600 N, determine their required spacing along the beam.
The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
a. calculate the value of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. d. Calculate the nominal block shear strength based on possible failure paths