A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section that is 16 in. deep. Each plank has a width of b- 4.3 in. The cantilever beam has a length of L - 5.9 ft and it supports a concentrated load of P- 3500 Ib. (a) Calculate the magnitude of the horizontal shear stress at points A, B, C, and D. (b) From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam. 2 in. (typ) B 16 in. Answer: TA i psi Te- i psi TC-i psi TD- i psi Save for Later Attempts: 0 of 1 used Submit Answer

A cantilever wood beam consists of eight 2 in. thick planks glued together to form a cross section that is 16 in. deep. Each plank has a width of b- 4.3 in. The cantilever beam has a length of L - 5.9 ft and it supports a concentrated load of P- 3500 Ib. (a) Calculate the magnitude of the horizontal shear stress at points A, B, C, and D. (b) From these results, plot a graph showing the distribution of shear stresses from top to bottom of the beam. 2 in. (typ) B 16 in. Answer: TA i psi Te- i psi TC-i psi TD- i psi Save for Later Attempts: 0 of 1 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How to solve for the centroid of the composite body using the principle of moments and treat each part as a finite element of the whole figure (show a step by step solution)
A simply supported beam carries a concentrated load at the center which fluctuates from a value of W to 4 W. The span of the beam is 470 mm and its cross-section is circular with a diameter of 57 mm. Take ultimate stress of beam material as 683 MPa, Yield stress as 0.55 times ultimate stress and the endurance strength as 0.45 times the value of ultimate stress and take a factor of safety of 1.5. Calculate the maximum value of "W", if the variable stress induced in the beam is 109 N/mm?. Using Goodman relation calculate the value of mean stress in N/mm?. **Note: Please upload your handwritten working/solution to the link provided. Maximum Bending Moment Minimum Bending Moment Mean Bending Moment Variable Bending Moment Section Modulus, Z mm3 The value of Load "W". in N The value of Mean stress using Goodman relation ..
A square hollow steel structure with a wall thickness of t1 = 10 mm is pin linked to two gusset plates with a thickness of t2 = 12 mm, which are welded to a base plate with a thickness of 12 mm and secured to a concrete base with 4-16 mm diameter anchor bolts. The pin has a diameter of 16 mm. P = 48 kN compressive load, 30 deg. P= 48 kN Stnt gusset plate fy=12 mm 0=30 10 m 12 mm 16 mm ø anchor bolt 4-16 mm p 1. Determine the bearing stress in MPa between the struct and the pin. 2. Calculate the pin's shear stress in MPa. 3. Determine the anchor's shear stress in MPa.
Material is CONCRETE. Please check all criteria and show work clearly.
anwser part 4
A steel I-beam has a web that is 17inches tall and 0.19inches thick. If the max shear in the beam is 6kips, what is the approximate max shear stress in the beam in psi? Type your answer...
2. Per ACI318-19, choose the correct value of the strength reduction factor ø for the flexural capacity of a beam with ɛ = tension face. 0.0032, where & is the strain for steel reinforcement closest to the (A)0.9 (B) 0.85 (C) 0.75 (D)0.65
need answers pls and solutions asap, thank you!
The beam shown left below has the cross section shown right below. Determine(a)The maximum tensile fiber stress in the beam.(b)The maximum compressive fiber stress in the beam.(c)The shearing stress 50 mm below the top surface of the flange.(d) The maximum shearing stress