The given igune chows a Eylinden ol um diameren in c quilibenium calcwlale the ven licae component ol the hounce exented by Hhe Huid pen melen lengih ol the cy linden.

Q: A can of soft drink at a temperature of 4 deg C is taken from a refrigerator into a room where the…

A: The temperature of the can is .The temperature of room is .The relative humidity is .

Q: 180 180 120 仁30

A:

Q: m/s" that means the flow is: In a horizontal flow of incompressible fluid along a constant pipe…

A: In a horizontal flow of incompressible fluid along a constant pipe section under steady conditions,…

Q: 11.20 (B). A steel rod, of flexural rigidity El, forms a cantilever ABC lying in a vertical plane as…

A: Introduction: The deflection refers to the displacement of a beam or node from its initial position…

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: Which et h

A: introduction: Forging is a manufacturing technique that involves pounding, pressing, or rolling…

Q: Suppose that A24 . Eaun) • Part C Determine the coordinate direction angie of the resutant force of…

A:

Q: (c) The type of pressure plate chosen as a result of the calculation in part (b) of this question…

A: A clutch is a device that allows two elements with a common axis of rotation to connect and detach…

Q: Lind Osthogonal tsajctosies 6aX whese a pabometeb

A:

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: The hand brake for a bicycle is shown. Portions DE and F G are free to rotate on bolt A which is…

A:

Q: A 2-cm square cross-section steel part having a Brinell hardness of 100 and a length of 4 cm is to…

A:

Q: The y-coordinate of a particle in curvilinear motion is given by y = 7.8t³ - 13.3t, where y is in…

A: Given that :In the y-coordinate as,                                    Also, acceleration in x-axis,…

Q: Q3: The uniform beam has a mass of 50 kg per meter of length. Determine the reaction the supports.…

A: GIVEN:

Q: The flow is said to be steady when the: For the Velocity at any point of observation does not change…

A: Introduction A fluid's flow is steady when its velocity, pressure, and all parameters of its…

Q: 30 mm 150 mm y 30 mm 150 mm The moment of inertia (in mm) about the axis of symmetry is nearest?

A:

Q: peom t (つとやr) 8HF1 DETERMINE THE 3 RE he T IONG FOR THE BENM SHOLIN BOVE.

A:

Q: Determine the magnitude of the force which member CD exerts on the pin at C. A 30% B 0.49 mi Answer:…

A:

Q: * Ce fea dendn D d f N

A: Normal stress is defined as the intensity of force acting over a unit area in perpendicular…

Q: Deive equabon for height Rof Pate Governer useig Instantenous Centre Method.

A:

Q: Quizs- Replace the loading system by equivalent resu/tant Force and Couple wmoment acting at Point…

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Q: Problem 1) The two bars are made of a material that has the stress-strain diagram shown below. The…

A: To find: The cross-sectional area of each bar, so that the bar fracture simultaneously. Given: The…

Q: 15 kip-ft Given are the following data in the figure. Determine what statement is correct if G is 12…

A:

Q: Prove that CIpoise = 0.1 dyne.sec cm2

A: Poise: The poise is the unit of dynamic viscosity. The unit of the viscosity is N·sm2 in the SI…

Q: A measurement device is constructed from two (identical) uniform bars, welded together at right…

A: 1. Moment of inertia of the welded bar about pivoted point O,

Q: Q3: You have a truss which is shown below, two forces applying on it in B and C joints, which are…

A:

Q: fead He nearuremeat of the MCrOmeler (c) 10 15 20 -20 0-25 mm

A:

Q: 4. Air flows steadily at the rate of 0.4 kg/s through an air compressor, entering at 6 m/s with a…

A: Given: The mass flow rate of air, m = 0.4 kg/s The air velocity at compressor entry, V1 = 6 m/s The…

Q: Inside section 20 mm. a helical sping of circulat crols in dianetu. another placed having the sping…

A: Springs are one of the flexible machine elements, which gets deformed when load is applied to it and…

Q: Sokte

A: The value is 720 according question

Q: 4Anal lubaricant is put between twe camxial. cylindexs. Ghe cuter. is xotuting arith aunequlax.…

A: Solution: Given Data: ω=80 cycles/secR=5 cmc = 0.4 mmTo=70oCV=0.75 cm2/sρ=1.25 g/cm3k=0.0056…

Q: G For agivern line: 0151-31 Encd: True teng Th of The Line eD- 5lofe cnglefek The line @ verticaed…

A: (a) Write the co-ordinates of points C and D.   Cx1,y1,z1=1,2,2Dx2,y2,z2=5,1,-3   Write the…

Q: For the acceleration equation, when the term VdV/ds-2 m/s² that means the flow is: In a horizontal 0…

A:

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.