15 kip-ft Given are the following data in the figure. Determine what statement is correct if G is 12 million.

Q: State three uses of the combination set

A: Combination set is an measuring tool, it is used to measure angles and lengths.

Q: How many turns does cog E make?

A:

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Why is 100 at - here?

A: Why is 100 at - here?

Q: The pictured disk which weighs 20 lbs. and contacts an inclined surface (this inclined surface is…

A:

Q: Convert the decimal number 35710 into its octal number equivalen

A: Steps Write the given decimal number. If the given decimal number is less than 8 the octal number…

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: Part C - Radius of curvature for AB and BC Determine the radius of curvature for AB, PAB, and for…

A:

Q: salve gine a- when

A: givendifferential equation xdydx+cosy=0y=π4  when x=2

Q: S (-36mm) is correct but total distance traveled (166.04 mm) was marked wrong can you help me?

A:

Q: Ax R.70 4x 1.40 B This part contains 4 holes with radius 0.375 inches 1.00 This part contains 4…

A: Select the correct statement about the notation circled in green and marked as letterA. Assume all…

Q: what is the MMC of shaft dimension 1.375 /- .030?

A: Given: The dimension of shaft  is 1375/-0.30 MMC :MMC stand for  Maximum Material Condition.

Q: If the main scale reading(mm) and vernier scale reading (division) are 16 and 9 respectively for a…

A: It is a precision instrument with a low least count, and is used to take sub-millimeter dimensions…

Q: Find ex, ey and y. NOTE: ex and ey in mm/mm and y in radians.

A:

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: What is the SAE horsepower of an 8-cylinder engine with a bore of 4.556 inches? Round to the nearest…

A: Given data:- no of cylinder (n)=8 bore (d) =4.556 inches To find:-the SAE horsepower

Q: How did you get theta =45?

A: Consider following given figure of a structure.here we need to determine the angle between member DE…

Q: Your selection was a gas-turbine power plant operating on an ideal Brayton cycle and according to…

A:

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: Find the angle e for the given figure 800 N y 8 3 O a. 63 О ь. 59 с. 69 O d. 66

A: From the given figure...

Q: Shaw thent pve= Constant For achabatic proass. an %3D

A: The term "adiabatic" refers to a process in which there is no heat transmission. This does not…

Q: 4 mefeor is aout l a gang and is velocity is 4epined by ve t-5, whare is in seconds. Find fre

A:

Q: Determine ly and ky.

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: 4 Am ob jecet is made p fravel obrerver çees fhat it is fraveluing harizbufally fx= 24t° M/ where…

A:

Q: y D 1 m FD

A: Given data:     The given load is: FD=100 kN The given angle is: θ=73˚ The distance between the load…

Q: Q34 gine exCumphe far nolineer operautor an

A: Given: To give an example of non-linear operator.

Q: State four espect to consider before selecting correct solvant

A:

Q: Please show the computation in solving for NB and FAB

A:

Q: 02 2N Find markdore.

A: Given data : The value of force applied F=2 N The value of Distance moved by an ball d=1.1   To find…

Q: travelling hoizoniany obenier fees ma where t is in seconds. What s the magnitude and vecE of the…

A:

Q: a boe is foaveling parth of How/ong illake par the bus reach la5 on sap a conctant speedf a

A: Given:v=17 m/sS=5 km =5000 m

Q: 3.A ball is torsed at s0 m/s at an k the maximum range of the ball and lhcight if the ball was…

A:

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Thermodynamic Relations

Thermodynamics is the division of physics that deals with the transfer of any kind of energy, whether it be heat, temperature, or work, from one object to another.