The given circuit uses a T network to match the impedance between the source and the load for maximum power transfer. A 60 Hz source has a series impedance of 50 +5. What load impedance would a T network with Ls 0.485 H, C-25.4 μF, and LL 0.566 H correspond to for maximum power transfer? (Round the final answer of RL to three decimal places.) Source T Network Load Rs+jxs Ls m LL m C ' R₁+jXL The maximum power transfer will occur when RL is 57.663 Qand XL is 0

The given circuit uses a T network to match the impedance between the source and the load for maximum power transfer. A 60 Hz source has a series impedance of 50 +5. What load impedance would a T network with Ls 0.485 H, C-25.4 μF, and LL 0.566 H correspond to for maximum power transfer? (Round the final answer of RL to three decimal places.) Source T Network Load Rs+jxs Ls m LL m C ' R₁+jXL The maximum power transfer will occur when RL is 57.663 Qand XL is 0

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

(a) Transform v(t)=75cos(377t15) to phasor form. Comment on whether =377 appears in your answer. (b) Transform V=5010 to instantaneous form. Assume that =377. (c) Add the two sinusoidal functions a(t) and b(t) of the same frequency given as follows: a(t)=A2cos(t+) and b(t)=B2cos(t+). Use phasor methods and obtain the resultant c(t). Does the resultant have the same frequency?
Kindly choose the appropriate and best answer.
-The Vollage V= 100210°V is 62 pplied across a capacilive 1oad . The 1-a kes ap paraal' Power Load of 500VA teading Power fracl-or. The reaclance (xc) of load 's---- 7
4- A Circuit of zero lagging power factor behaves as a. A capacitive circuit b. An inductive circuit c. RC circuit d. RL circuit
The type of the load whose current and voltage phasors are as shown in the phaser diagram is Im 90° - Re Pure capacitive load non-pure Inductive load Purse resistive load O Pure inductive load non-pure capacitive load
Application: Construct the circuit in figure. R= 2,2KN, L = 1 mH, and C= 10 nF. L Necesssary Formulae: 1 Xc 2.π.f.C X.-2. π.f. L By using the formulea perform the calculations of Xc and XL then fill the table. f (Hz) Xc XL 50000 60000 70000 80000 90000 100000 110000 120000 130000 140000
For the circuit diagram in figure Q22: which of the following is the total impedance? 12 Ri 10R R2||5R Figure Q22 V 220V40 50HZ L1 315mH C1=350uF O a. 3.33/0° O b. 4.71290°2 O c. 7.3304-19.66° O d. 10.37261.19°2
Find the voltage and current across R,L,C Include phasor diagrams and impedance triangle
Three impedance Za= (3+j4) ohms, Zc= (4-j4) ohms and Zr=0+j3 ohms are connected in parallel. Solve for the pf of the combination.
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
Solve this fast please
Using superposition, determine the current through the inductance XL for each network in the figure