The forklift weighs 3500 lb and carries an 800-lb shipping container. There are two front wheels and two rear wheels on the forklift. (a) Determine the contact forces between the wheels and ground. (b) How heavy a load can be carried before the forklift will start to tip about its front wheels? (See Figure 4.21.) 800 lb ` B +24>-42→e-30→ 3500 lb in. in. in. 2F 2R

The forklift weighs 3500 lb and carries an 800-lb shipping container. There are two front wheels and two rear wheels on the forklift. (a) Determine the contact forces between the wheels and ground. (b) How heavy a load can be carried before the forklift will start to tip about its front wheels? (See Figure 4.21.) 800 lb ` B +24>-42→e-30→ 3500 lb in. in. in. 2F 2R

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller at B on a smooth surface. If the pin support at A suddenly fails, calculate the magnitude of the force of the roller at B acting on the beam at that instant, by modelling the beam as a uniform slender bar. Present your answer in lb using 3 significant figures. 4 13 1000 lb -8 ft- B -2 ft-
The block in the figure below has a mass m. The coefficient of static friction between the block and the inclined surface is ug. Determine the smallest magnitude force P to prevent motion. Take: m = 80 kg, e = 30°, a = 20° and us = 0.20. P= 294.36 N P= 460.48 N P= 392.40 N P= 376.18 N P= 250.28 N
Find the forces (F1,F2,F3 lb) in Fig. 364. (A=27, B=64, C=44) deg, (D=4, E=3, F=4) ft, F4=5440 lb If F4 is negative, then the direction of F4 is down. A negative answer indicates that the direction is reversed. Answers can be checked by demonstrating that components balance.
Two identical uniform sticks of mass m and length I are pinned together. They both make an angle with respect to the vertical. A massless string is connected to the bottom of one rod and perpendicularly to the other rod as shown in the figure below. Determine the tension in the string if the table, on which the sticks are located, is frictionless. Solve this problem by balancing forces and torques, and applying the principle of virtual work. = N₁ + N₂ Samg | tl.mg. zl.mg. ·sind + T. l. 00:20 = N₁. l. sind sind + Il cosse N₂. l. sing N₁= N₂ = N* mg + sind + [ 11-2in²0 ) = sind T=_sing 2-4 sin
The grey block D in the sketch has a mass of 100 kg. The blue wedges (B and C) have a mass of 10 kg. Between A and B: usAB=0.3 Between B and C: usBC=0.2 Between C and A: μsCA=0.3 Between C and D: μsCD=0.4 Between A and D: μsAD=0.5 Determine the minimum value of force P that must be exceeded to initiate movement in block D. A B B D
The lifting arm shown below needs to lift a weight of 4 (N). Assuming the links are weightless, determine the magnitude of the force being applied by the pin at B on the lifting arm to the nearest hundredth of a newton. 10Em) 6icm- 150 A Servo Horn Arm 4 (W) 'Servo
Consider (Figure 1). The cord is attached to the 36-lb block, and the coefficients of static friction are HB = 0.2 and μp = 0.3. Figure M 1.5 ft B 3 ft -1.5 ft- D C < 1 of 1 Part A Determine the smallest couple moment which can be applied to the 24-lb wheel that will cause impending motion. Express your answer in pound-feet to three significant figures. VAΣo↓↑ vec M = Submit Provide Feedback Request Answer A ? lb-ft
O Week6 Friction_21-22.pdf ds/Week6_Friction_21-22.pdf 4. The mine car and its contents have a total mass of 6000kg and a centre of gravity at G. If the coefficient of static friction 10 kN Doo→ between the wheels and the 0.9 m • G tracks is u = 0.4 when the wheels are locked, find the normal force acting on the front wheels at B and the rear /0.15 m A 0.6 m 1.5 m- wheels at A when the brakes at both A and B are locked. Does the car move? [Ans. NA = 16.5 kN, Ng =42.3 kN, the car does not move] ily TWO WAY POWER 09889 NO MODE SETUP
Q.3) The coefficient of friction between the 120 lb block (shown in figure below) and the incline plane is 0.3 and that between the cord and cylindrical support is 0.4. Determine the range of cylinder weight W for which the system shown below will be in equilibrium. μ = 0.3 120 lb 24° <μ = 0.4 5 W
Given the figure shown below, what is the mass of block B on the smooth incline if the system is in static equilibrium? A rope runs from block B up around the frictionless pulley at A down to a 10 kg counterweight. A 1 m B- 1m 10 kg 45°
1)→ In the figure-below, find-the-forces-in-members AD, ED, and AB.-Can-the-forces-in-all-the- members of this-truss be found-from-statics equations alone? Why-or-why not? 50 lb 2 ft F G -3 ft- E A 3 ft. D -3 ft- B 100 lb 80 lb с
b = 2.05 m Submit Previous Answers With its engine removed, the mass of the car shown in ( Figure 1) is 1400 kg and its center of mass is at C. The mass of the engine is 300 kg. ✓ Correct Figure T 0.45 m > 1 of 1 Part B Review If the car is parked on a 15° slope facing up the slope, what total normal force is exerted by the road on the rear wheels B? Express your answer using three significant figures and include the appropriate units. ? UA 0.6 m A-1.14 m- B B = Value Units b. -2.60 m- ་ Submit Previous Answers Request Answer × Incorrect; Try Again