Part BDetermine the y-component of reaction at support A.Express your answer to three significant figures and include the appropriate units.Ay =SubmitPart CA₂ =SubmitPart DμÀDetermine the z-component of reaction at support A.Express your answer to three significant figures and include the appropriate units.B₂ =ValueSubmitRequest AnswerμÅValueRequest AnswerμAUnitsDetermine the x-component of reaction at support B.Express your answer to three significant figures and include the appropriate units.ValueRequest AnswerUnitsB] ?Units?? The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD, as shown in (Figure 1). The supports atA and B are in proper alignment and exert only force reactions on the rod. Take F = {35i +45j - 90k} N.FigurePart ATCD=μÅValue0.5 mDetermine the tension within cable CD.Express your answer to three significant figures and include the appropriate units.Submit Request Answer0.5 mxBUnits2 m?1 of 1

Answered: Image /qna-images/answer/997b9f1e-2ffa-4951-a742-6570daca3d0b.jpg

The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD, as shown in (Figure 1). The supports at A and B are in proper alignment and exert only force reactions on the rod. Take F = {35i +45j – 90k} N.

The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD, as shown in (Figure 1). The supports at A and B are in proper alignment and exert only force reactions on the rod. Take F = {35i +45j – 90k} N.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 1 Consider the pipe segment AB that lies in the az-plane and is bent in a circular form with radius 4 m. The pipe is supported at A by an unknown support and at B with a cable BC. B' A50 4 m If the support at A can resist a maximum cou- ple moment of 1 650 Nm, determine the small- est force F that will cause the support to fail. F 6 m D 6 m
Solve using Force Method- Consistent Deformation. (Both support are fixed) 1. Solve for reactions 2. Draw M, m1,m2,m3 3. Compatibility Equations 4. Value of x1, x2, x3
a. The ends of the triangular plate are subjected to three couples. Determine the magnitude of the force F so that the resultant couple moment is 400 N-m clockwise. 600 N 600 N F 35° 35° 1m 250 N 250 N
Part I. Principle of Superposition. For the beam loaded as shown, it is required to determine the distribution of internal forces and moments on the beam. El is constant. The supports at B and C are rollers and D is pinned. 10 kN 3 kN/m 3 kN/m В A 3m 3m D 3m 4 kN 1. Determine the degree of indeterminacy of this beam. 2. Solve for all the support reactions. 3. Draw the shear and bending moment diagram for the beam.
Determine the magnitude of the tension at Support B (N).
. Due to a certain horizontal force 'P' on the frame shown below, the moments are as follows MAB=5 kN.m (Anti clockwise) MBA = 10 kN.m (Anti clockwise) McD = 6 kN.m (Anti clockwise) The force 'P' is B om 8 P 5 m A 2 m C 3 m D
3KN G 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. B. SOLVE THE RESULTANT OF HORIZONTAL AND VERTICAL REACTION AT HINGE SUPPORT. C. SOLVE THE FORCE IN MEMBER AB, AC, BC, BE, AND BD. 1m H
QUESTION 1. Determine the reaction at pins at A, B and C and fixed support at D. Answer in component form. Take P = 8+ 0.5(third highest digit of your student number). ALSO, draw the shear and moment diagram of member BC only. 12P kN 8P kN B 4 m D -3 m 3 m- 3m 3 m-
5 - In the plane truss system, whose loading condition is shown in the figure, there will be support reactions A and B, and rod forces 1,2 and 3. A is the fixed joint and B is the sliding joint. Loads on the beam P = 50 kN, All acute angles in the truss system are 45 degrees. Accordingly, S2 = ? a) 0B) 175C) 225D) 35.36E) 200
PP A BỊ In the plane truss system, whose loading condition is shown in the figure, there will be support reactions A and B, and rod forces 1,2 and 3. 6 - A is the fixed joint and B is the sliding joint. Loads on the beam P = 50 kN, All acute angles in the truss system are 45 degrees. Асcordingly Bу 3D? O a) 0 O B) 175 O C) 225 OD) 35.36 O TO) 200
Determine the vertical and horizontal reactions of each support on the following figures. Assume that the weight of the beam is SN Kilonewton. FN= 78 SN= 51
Please help me