The forging hammer shown in Figure P13-43 is subjected to a surface temperature of 210°C acting on the lower flat surface of the steel hammer head. The hammer's thermal conductivity is 20 W/m-K and the room temperature is assumed to be 40°C with a convection coefficient of 3.216 x 10-6 J/(s-°C-mm²). Determine the temperature distribution throughout the hammer.

The forging hammer shown in Figure P13-43 is subjected to a surface temperature of 210°C acting on the lower flat surface of the steel hammer head. The hammer's thermal conductivity is 20 W/m-K and the room temperature is assumed to be 40°C with a convection coefficient of 3.216 x 10-6 J/(s-°C-mm²). Determine the temperature distribution throughout the hammer.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can someone please help me with creating an excel spreadsheet to calculate heat transfer phenomenon from a cylindrical fuel rod to the coolant? The excel sheet needs to be able to calculate these 3 things: Heat generated in a fuel rod at a distance ‘r’ from the center; Total Heat generated in the Reactor; the maximum temperature in the fuel and the cladding surface temperature, for a fuel rod at a distance ‘r’ from the center. The fuel used in this will be UO2 and there is a thin layer of helium that will separate the fuel from the cladding material. The user input parameters will be: the thermal neutron flux at the core, thermal conductivity of fuel, thermal conductivity of helium, thermal conductivity of the cladding, thickness of the helium layer, thickness of the cladding, diameter of the fuel pellet, fuel rod location (r), Cylindrical Reactor Size, and the fuel enrichment. For the fluid the user input will be coolant temperature and the heat transfer coefficient.
EXAMPLE = wire Consider a long resistance wire of radius ₁ 0.2 cm and thermal conductivity k = 15 W/m . °C in which heat is generated uniformly as a result of resistance heating at a constant rate of g = 50 W/cm3. The wire is embedded in a 0.5-cm-thick layer of ceramic whose thermal conductivity is k = 1.2 W/m °C. If the outer surface temperature of the ceramic layer is measured to be Ts = 45°C, determine the temperatures at the center of the resistance wire and the interface of the wire and the ceramic layer under steady conditions. ceramic 17 Interface Mech. Eng. UOK Wire Ceramic layer T₁=45°C ۳۰/۱۰/۲۰۱۳
A multi-layered wall with the dimensions shown in the figure has temperatures of 200°C and 50°C over the left and right surfaces, respectively. If the thermal conductivities of the wall materials A and C are k-60 W/m-K, k-24 W/m-K. If total rate of heat transfer through the wall is 175 W, what is the thermal conductivity of material B? T- 200°C T-soc 6 cm- 2 om 25 om
This question requires the use of the conduction charts given in the appendix at the end of this paper. A wooden sphere of diameter 5 cm is initially at a uniform temperature of 21 °C. Its surface temperature is suddenly raised to 83 °C. The thermal conductivity and thermal diffusivity of the wood are 0.15 W/m K and 0.82 x 10-7 m2/s, respectively. a) Calculate the temperature 2 cm beneath the surface of the sphere 30 min after the sudden increase in temperature. b) Calculate the energy gained by the sphere during this time.
A steel rod, which is free to move, has a length of 200 mm and diameter of 20 mm at a temperature of 15°C. If the rod is heated uniformly to 115°C, determine the length and the diameter of this rod to the nearest micron at the new temperature if the linear coefficient of thermal expansion of steel is 12.5 x 10 m/m/°C. Wrong solution will be reported instantly
An uninsulated steam pipe passes through a room in which the air and walls are at 25°C. The outside diameter of the pipe is 88 mm, and its surface temperature and emissivity are 200°C and 0.80 respectively. If the coefficient associated with free convection heat transfer from the surface to the air is 15W/m2-k, what is the rate of heat loss for a 5 meter pipe? Round your answer to 2 decimal places.
1- Microwave radiation is incident on one side of a planar wall with a heat conductivity coefficient k. (x=0) -D°b=(x)b leads to volumetric heating. While this surface is 9(W/m²) microwave radiation is fixed. kept at a constant temperature To, the other surface at x=L is very well insulated. Determine the temperature distribution T(x) in terms of x, L, k, qo and To.
Required information Consider a 5-m-high, 8-m-long, and 0.22-m-thick wall whose representative cross section is as given in the figure. The thermal conductivities of various materials used, in W/m-K, are kA=kF=2, kg-8. kc-20, kp=15, and ke-35. The left and right surfaces of the wall are maintained at uniform temperatures of 345°C and 100°C, respectively. Assume heat transfer through the wall to be one-dimensional. Disregard any contact resistances at the interfaces. 1 cm. A4 cm B 4 cm रेव 4 cm Sem 6 cm DI 4 E 6 cm F 10 cm 6 cm 100°C 8m Determine the rate of heat transfer through the wall (in W).
A 10 cm-thick beef steak is being frozen in a -40°C room. The product has 73% moisture content, density of 970 kg/m³, and thermal conductivity (frozen) of 1.1 W/(m K). Estimate the freezing time using Plank’s equation. The product has an initial freezing temperature of -1.75°C, and the movement of air in the freezing room provides a convective heat-transfer coefficient of 10 W/(m² K). a. tf =... h
7. A composite wall consists of three materials, as shown in Figure 2. The inside wall temperature is 200°C and the outside air temperature is 50°C with a convection coefficient of 10 W/m²-K. Determine the temperature along the composite wall. Where A is the area of cross- section (can be taken to be equal to 1) and k is the conductivity. Problem is governed by the equation d²T -kA- = 0, 0
The lining of box-type fumace is made up of a refractory layer and steel plate as shown in the figure. Steady state temperature at the surface of the refractory is 1273 K and that at the outer steel surface is 473 K. If the steady state heat flux through the refractory-steel plate composite is 1600 W/m², and heat flow is along x-direction only, the thermal contact resistance (m² K/W) between refractory and steel is_ steel Refractory 1273K Furnace 473K Ambient Given data: Thermal conductivity of refractory = 1.2 W/m-K Thickness of refractory lining = 80mm Thermal conductivity of steel = 32 W/mK Thickness of steel plate = 4mm