The force P is applied to the 32-kg block when it is at rest. Determine the magnitude and direction of the friction force exerted by the surface on the block if (a) P = 0, (b) P = 132 N, and (c) P = 195 N. (d) What value of P is required to initiate motion up the incline? The static and kinetic coefficients of friction between the block and the incline are µg = 0.26 and Hk = 0.20, respectively. The friction force is positive if up the incline, negative if down the incline.

The force P is applied to the 32-kg block when it is at rest. Determine the magnitude and direction of the friction force exerted by the surface on the block if (a) P = 0, (b) P = 132 N, and (c) P = 195 N. (d) What value of P is required to initiate motion up the incline? The static and kinetic coefficients of friction between the block and the incline are µg = 0.26 and Hk = 0.20, respectively. The friction force is positive if up the incline, negative if down the incline.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam and the loading as shown in figure below, determine (1) the slopes at 2 and 3, (2) the vertical deflection at the midpoint of the distributed load. 12 kN/m 1m E 200 GPa 2 1 m. I= 4 x 10 mm 3
4. A 25 mm diameter shaft is pulled through a cylindrical bearing as shown (not rotating). Oil is used as a lubricant and fills the 0.3 mm gap between the shaft and the bearing. The kinematic viscosity of the oil is 8.0 x 10-4 m²/s and the specific gravity is 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear (i.e. Couette flow). Draw the free body diagram and show the forces. Bearing Shaft 0.5 m- Lubricant
Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa, a1=a2= 12x10 /°C, AT= -25 °C , h= 1700 mm, 0 = 65° (1) (2) Q2/ Determine the magnitude of applied load P. Assume: A1 = 500 mm?, E1 = 70 GPa, a1= 22x10/°C, AT= -30 °C, E = 1150 x 106 mm/mm, h = 3.75 m, a 1.75 m,b 1.25 m D (1) B
The cross section of a quarter circular concrete block JKL as shown in Figure 5 is located at thebottom of a reservoir. The width (perpendicular to the paper) is 3 m. The specific weight of theconcrete block is 24 kN/m3. The coefficient of friction between the base of the block and thefoundation is 0.43. Determine if the concrete block is stable or not against sliding and overturningif the water is:A. At side XB. At side Y, with the same water level as A.
Show complete solution pls
Compute the total elongation caused by an axial load of 142 kN applied to a square bar, tapering from a width of 120 mm to 40 mm in a length of 10 m as shown. Assume E = 214 GPa. Answer must be in mm. 120 mm 40 mm Area = A %3D P kN P kN A Bf L = 10 m %3D
working stress method
Kindly answer correctly. Please show the necessary steps. Thanks in advance.
Determine the location and magnitude of the maximum absolute deflection in AB between A and the center of the beam. (b) Assuming that beam AB is a W460 *113 rolled shape, M0 = 224 kN·m, and E = 200 GPa, determine the maximum allowable length L so that the maximum deflection does not exceed 1.2 mm.
1. A typical cross-section of a roinforced concrete T-beam is shown in the figure below. The beam is reinforced with eight 25 mm diameter bars in tension zone. For the purpose of analysis, use the effoctive depth of 575 mm. Use f. = 25 MPa and f, = 420 MPa. Determine øM, 1000 mm T100 mm 8-D25 300 mm 575 mm ww G29
Dont forget to draw the FREE BODY DIAGRAMS ALSO PLEASE! (: