A reinforced concrete beam has a width of 300mm. The beam has a tension steel area of 1834.04 mm^2. Steel strength concrete strength is 28 Mpa. 420 Мра and What is the effective depth if tension strain et = 0.01 what is the ultimate moment of the beam Select the correct response: d = 450mm Mu = 274.46 KN-m d = 500mm Mu = 343.6 KN-m = 500mm Mu = 309.24 KN-m d = 550mm Mu = 382.11 KN-m d = 550mm Mu = 343.9 KN-m = 450mm Mu = 305.09 KN-m

A reinforced concrete beam has a width of 300mm. The beam has a tension steel area of 1834.04 mm^2. Steel strength concrete strength is 28 Mpa. 420 Мра and What is the effective depth if tension strain et = 0.01 what is the ultimate moment of the beam Select the correct response: d = 450mm Mu = 274.46 KN-m d = 500mm Mu = 343.6 KN-m = 500mm Mu = 309.24 KN-m d = 550mm Mu = 382.11 KN-m d = 550mm Mu = 343.9 KN-m = 450mm Mu = 305.09 KN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a simply supported prestressed concrete beam, compute the stress in the top fiber at the centerline. Properties of the beam are: Width of the beam, b: 335 mm; Depth of the beam, d: 371 mm; Eccentricity of the beam, e: 170 mm; Prestressing Force, P: 743 KN; Superimposed Load, w: 5 KN/m; Length of the beam, L: 12 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) P. 000
A reinforced concrete T-Beam has a width of 800mm and a thickness of 50mm. It has an effective depth of 300mm and is reinforced at the bottom with a total steel area of 1800sq.mm. If the web thickness of the T-beam is 200 mm, with a concrete strength of fc' = 20MPa and yield strength of steel fy= 400MPa. Assume steel yields. The value of compressive force of concrete is kN. A. 720kNB. 810KNC. 660kND. 940kN
A reinforced concrete beam has a width of 300mm and an effective depth of 580mm. It is reinforced for tension only with 5-32mm diameter bars. Material strength are f'c= 24 MPa and fs = 130 MPa. Assume n=9. Use working stress design. Show complete solution and neat handwriting. 1) which of the following most nearly gives the location of the neutral axis from the extreme compression concrete? a. 272.42 mm b. 288.83 mm c. 256.77 mm d. 189.07 mm 2) which of the following most nearly gives the moment capacity of the beam? a. 255.73 KN.m b. 215.89 KN.m c. 238.16 KN.m d. 226.23 KN.m 3) which of the following is the condition of the beam? a. Over reinforced b. Under reinforced c. Balance condition d. Cannot Determin
Problem: Design a section of a concrete beam reinforced for tension only. The beam is simply supported on a span of 6.00 m and carries a load of 18 KN/m. Use Alternate Method of Design with n = 9. f'c = 20.70 MPa, Fy = 275 MPa. Use b = d/2. Write your solutions on clean sheets of bond paper, scan properly. Note: Clear concrete cover for the beam: 40 mm Clear spacing between rebars: 25 mm (minimum) Minimum bar size to use as per ACI Code: 16 mm diameter Design for flexure only.
A reinforced concrete beam (see figure)is acted on by a positive bending moment ofM = 160 kN . m. Steel reinforcement consists of4 bars of 28 mm diameter. The modulus of elasticityfor the concrete is Ec = 25 GPa while that of the steelis Es = 200 GPa.(a) Find the maximum stresses in steel and concrete.(b) If allowable stresses for concrete and steel areσac = 9.2 MPa and σas = 135 MPa, respectively,what is the maximum permissible positivebending moment?(c) What is the required area of steel reinforcement,As, if a balanced condition must be achieved?What is the allowable positive bending moment?(Recall that in a balanced design, both steel andconcrete reach allowable stress values simultaneouslyunder the design moment.)
An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2. If the average normal stress in the steel column must not exceed 140 MPa, determine the minimum required dimension “a” so that the bearing stress between the base plate and the concrete slab does not exceed 11 MPa.
1. Determine the following: a. Determine the moment of inertia of the section about its neutral axis. b. Maximum tensile stress in the beam c. Maximum compressive stress in the beam 300 N/m 625 mm T: 100 mm 500 mm A B 3 m 1.5 m 100 mm
b) A rectangular block of 1200 mm² cross-sectional area is subjected to a longitudinal compressive load of 1200kN. Determine the normal stress across the cross section of the block. If the block is cut by an oblique plane making an angle of 400 with normal section of the block. Determine: (i) Normal stress on the oblique plane (ii) Tangential stress along the oblique plane, and (iii) Resultant stress on the oblique plane.
A pre-tensioned rectangular beam 150mm wide and 300 mm depth is prestressed with three straight tendons each having a cross-sectional area of 50 mm? to an initial stress of 1200 N/mm?. The tendons are located at 100 mm from the soffit of the beam. If the modular ratio is 6 the loss of prestressing force (in kN up to one decimal place) due to the elastic deformation of concrete is
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. The concrete cover to bar centroid is 80 mm and at the bottom is 70 mm. use concrete strength f'= 21 MPa and steel yield strength fy=415 MPa for all bars. 1. Determine the tensile steel ratio when the beam is in positive bending. a. 0.01567 b. 0.01283 c. 0.01169 d. 0.01923 2. Determine the nominal moment capacity in kN-m of the beam in positive bending. a. 188.30 b.167.70 c.218.96 d.193.68 3. Determine the tensile steel ratio when the beam is in negative bending. a. 0.00406 b. 0.00475 c.0.00383 d. 0.00508 please provide a complete solution so I can understand. Very much appreciated to solve it early !!
A rectangular reinforced concrete beam has a width of 274 mm and an effective depth of 471 mm. Determine the maximum possible strength in (kn-m) of the beam for a singly reinforced condition. Use f'c = 30.79 MPA and fy= 414 MPA.
A 300mm x 500mm rectangular concrete beam is reinforced with four pieces 25mm diameter bars. The beam is simply supported on a span of unknown length. The uniform linear dead load from the slab is 18KN/m (weight of beam not included) and the uniform linear live load is 10kN/m. The effective depth of the beam is 430mm. the beam. Use area of one 25mm diameter bar = 510mm2. Using your own values of fc' = 20.1 MPa and fy = 335 MPa from the excel file, determine the safe length