The force P is applied at d = 50 mm from the bottom as shown. Compute the normal stress at section a-a at the specific points. B 200 mm P 200 mm d -300 mm- C- a A 20 mm

Q: Let strain rosette shown in figure computed the values of strains at the built in end and in NA of…

A:

Q: Pull In the figure above the yellow rectangle represents 68 degree F glycerin between two parallel…

A: The shear stress can be calculated using Newtons law of viscosity.

Q: Consider a point in a structural member that iS subjected to planestress. Normal and shear stresses…

A: Option (A) is correct.

Q: Q.2) A state of stress is specified as shown in Figure (2), By using Mo determine the normal and…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(40+802)2+502R=78.1…

Q: Calculate the stresses that will occur at point A in the adjacent figure. r=10mm

A: Given, Fz = 150 kNFy = 150 kNτ = 50 kN.mThere are three stresses at point A normal stress, bending…

Q: (MPa), 022=b+c+d+h (MPa), t12=c+g+h+d (MPa), O°=2(T1), E= 1000(T1) Mpa, v=(T1)/100 a) Calculate…

A:

Q: ) Determine the normal stress at point A. b) Determine the normal stress at point B

A:

Q: Check whether the beam section whose loading condition, cross section and dimensions are given in…

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter…

A:

Q: A pin- connected truss is loaded and supported as shown in the figure. Determine a. The normal…

A:

Q: b) In Figure Q1, an axial load P is applied at point D that is 5 mm from the geometric axis of the…

A: Iy = π/64(1204 - 1124) = 2.455 x 106 mm4  L = 2.8 m = 2800 mm

Q: Calculate the max torsional stress Tmax in N/mm2 on a solid circular shaft of diameter 19.57mm, if…

A:

Q: Plane Stress In the stress element given in Figure 3, WITH MOHR CIRCLE; (a) Determine the principal…

A: Principal stresses: Principal stresses are the utmost and minimum value of normal stresses on a…

Q: Solve the magnitude of the bar force of members AD, BD, CD, and CE

A: Answer  Let us first draw the free body diagram and calculate the reaction at the supports  Since…

Q: 10 mm 10 mm 8 kN -75 mm 75 mm 10 mm -70 mm -70 mm force of 8 kN, which is applied t cross-sectional…

A:

Q: Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution…

A: Given data: 1 grid square = 26 MPa Coordinate of y (2,3)

Q: 1. Determine the normal stress at bar AC. Use diameter of bar AC = 215 mm. 500 N 2 m 2 m

A:

Q: Question 1 Refer to the given figure as shown. P= 70 kN Cross section Area: 50mm x 50mm Modulus of…

A: Given Data:P = 70kNGross Sectional Area=50mm×50mmModulus of Elasticity = 70Gpa

Q: C Situation 7 - A rectangular bar 50 mm x 75 mm in cross-section is subjected to a tensile force P =…

A:

Q: The plane state of stress (shown in the following Figure) is for a point p inside a given body under…

A:

Q: If the beam is subjected to a shear force of V = 80 kN, determine the shear stress developed at…

A: Considering the section below:

Q: The bending moment Mx affects the cross section of the beam given in Figure 4. Beam cross section…

A:

Q: Q4) (2UMS): A state of stress is specified as shown in Figure (4), By using Mohr's circle determine…

A:

Q: Question 8 In order to determine the shear stress at A, using the shear stress formula, the…

A: To find the thickness, d for top flange and d for the portion below the flange and above A.

Q: Hi, i was wonderwing why with the normal stress at B the moment Mx * Cy is minus. can you explain…

A: From figure given below it is clear that the direction of moment about x-axis (Mx) and y-axis (My)…

Q: Find the normal stress and shear stress in the shaded plane using the MOHR circle for the element in

A: Given that:

Q: Question-2: The cross section of the bar in the figure a) Calculate the stress(tension) values at…

A: Find: (a) Stress at points A, B, C (b) Stress distribution in the section

Q: 1. The cross-sectional area of bar ABCD is "X" mm². Determine the maximum normal stress in the bar.…

A: The formula to calculate the normal stress is given by, σ=PA                    ...1 Draw the…

Q: In the cylindrical coordinate system, stress component Trz = 23 N/m². Trz acts on a surface (shown…

A: Given data : shear stress on r-plane along z direction = 23 N/m2 area of plane = 40 inch^2 find out…

Q: 70 mm 235 mm 30 mm 275 mm 30 mm 30

A: the force and balance system can be resolve by simplifying the mechanism. the force is transferred…

Q: A solid circular pole is subjected to linearly varying distributed force with maximum intensity qo…

A: Normal stress at the base 150MPa qo=6.9kN/m L=6m P=80kN

Q: The block shown in Figure 2 is subject to three forces. a) Determine the normal stress at point A.…

A: Given data  Point load  Dimensions  To find  Normal stress

Q: The strain components at a point in a body are given as: Exx = 12 ms, Eyy = 4 ms, and engineering…

A: Given: εxx=12 ms εyy=4ms γxy=-6 ms To find: a) The magnitude of the principal strains b) The angle…

Q: The curved bar shown in the figure has a rectangular cross section of 50x75 mm and an internal…

A:

Q: as shown in Figure (4), By using Mohr's circle determine the normal and shearing stresses and their…

A: Mohr's circle is a graphical representation of the equations for transformations of plane stresses.…

Pressure and Stress