Answered: The force on a wagon wheel is F=2000 N.…

The force on a wagon wheel is F=2000 N. Find the axle diameter of the wagon wheel made of Fe50 material. Given: GAK=2900 daN/cm2, S=2 F/2 a=70

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.10P: Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.

See similar textbooks

Similar questions

4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
please give neat and clean answer ill give upvote with proper digram if required
Finding the bar forces by the nodal point method
The linkage shown is used in a vehicle suspension system. Find the forces indicated below when a static force of F = 820 lb is applied to the tire at point C at an angle of 0 = 22° as shown. Assume the connection of the wheel to member AB is rigid. hs hy hi F BY NC SA W4. W, Ws 2013 Michael Swanbom Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value Variable Value hi 10 in Wi 8.8 in h2 15.6 in W2 5.6 in h3 18.1 in W3 10.8 in h4 10.9 in WĄ 7.4 in h5 4.9 in W5 9.3 in For all answers, take x as positive to the right and y as positive upward. At point B, member AB exerts a force of B = j lbs on member BHE. At point A, member AD exerts a force of A + j lbs on member AB. At point H, shock GH exerts a force of H = i + i lbs on member ВНЕ. At point E, the magnitude of the force exerted on the car body by member BHE is lbs. At point D, the magnitude of the force exerted on the car body by member AD is lbs. At point G, the…
A worker applies forces P = -10i + 8j Ib and Q = 10i Ib to the handle and clamping bar of the power drill. These forces are equivalent to the force R= 8j Ib acting on the drill bit and the couple CR = -120j Ib - in. Determine the dimensions a and b. S in.
The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F = 800 N
Could you help me with the first few steps on solving this using vectors? I need to calculate the forces in AB and BC. I don't the answer right away but I don't know where to start.
1. A tripod shawn supports of note that ball and rocket joints are used to mount the tripuod a load P=1000N at point A. Take at points B,D, and C. consider the t LI L 2 L2: 4 L3 : 3 A : 45° g :30° %3D on x-z plane L2 POINT C (2,-2,3) C0,0,0) ミー- Determine the ff Force of AB - N Force of AC - N Force of AD : N
the bent bar AB weighing 10lb/ft is mounted as shown in figure 2 upon a carriage weighing 250 lb. The center of gravity of the carriage is at C midway between the wheels. If P=108lb and there is no frictional resistance at the wheels, find the wheel reaction R1. find the vertical component of the hinge force at A. find the horizontal concept of the hinge force at A.
The two bearings (B1) and (B2) are used to support a shaft as shown in the figure Using the data given in the table below, (a) Calculate the following: (i) The radial force supported by Bearing-1 (B1) (ii) The radial force supported by Bearing-2 (B2) (ii) The axial force supported by Bearing-1 (B1) and Bearing-2 (B2) (iv) The equivalent force (P) supported by Bearing-1 (B1) (v) The equivalent force (P) supported by Bearing-2 (B2) (vi) The life in hrs. of bearing-1 (B1) (vii) The life in hrs. of bearing-2 (B2) (b) Comment on your results (Answer in one/two sentences only) Particulars Details Bearing Type (B1) Bearing Type (B2) Speed of Shaft (N) Dynamic load Rating (C) of Bearing (1) Dynamic load Rating (C) of Bearing (2) External Radial Force (Fr) External Axial Force (Fa) Deep Groove Ball bearing Cylindrical Roller Bearing 750 грm 120 kN 60 kN 25 kN 6 kN X =0.56, Y =1.6 Bearing Constants (ball bearing) Fr B1 B2 Fa 70 mm 100 mm
The cable carrying three 400-N loads has a sag at C of hC = 14 m. Calculate the following: 26.1 The magnitude of the tensile force in segment AB is Blank 1 N. 26.2 The magnitude of the tensile force in segment BC is Blank 2 N. 26.3 The magnitude of the tensile force in segment CD is Blank 3 N. 26.4 The magnitude of the tensile force in segment DE is Blank 4 N.
Calculate the reaction A of the pin on bar AD of figure *