toba.desire2learn.com/d21/le/content/547099/viewContent/3556691/ViewLof 1F₁+ Automatic ZoomProblem 1The force in cable AB is F₁ = 15 kN, while that in CD is F₂ = 15 kN. a = 2.0 m, b= 4.0 m, c =3.0 m, d = 1.5 m, e = 1.5 m, and f = 1.5 m. Determine the resultant R and the moment M, of theforce system with respect to point O.defVHEWLETT-PACKARDCF2

Answered: Image /qna-images/answer/f315e827-d1bf-40ba-99cd-052e42454215.jpg

The force in cable AB is F₁ = 15 kN, while that in CD is F2 = 15 kN. a = 2.0 m, b= 4.0 m, c = 3.0 m, d = 1.5 m, e = 1.5 m, and f = 1.5 m. Determine the resultant R and the moment M, of the force system with respect to point O.

The force in cable AB is F₁ = 15 kN, while that in CD is F2 = 15 kN. a = 2.0 m, b= 4.0 m, c = 3.0 m, d = 1.5 m, e = 1.5 m, and f = 1.5 m. Determine the resultant R and the moment M, of the force system with respect to point O.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3(): The pin B supports the 6 ft Load W= 9000 lb and connects horizontal cable with point A. If the pin C is W subjected to double shear 9 ft while pin at B is a single shear. The diameter of pin C is 1.5 in while the diameter of pin B is 0.8 in. Determine the shear stress at pins B and C. Also find the stress in the cable AB if its diameter is 0.5 in.
Consider that the catenary cable in the figure is anchored between supports A and B and issupporting only its own weight, which is w = 50 N/m.Determine the cable length, the minimum pulling force on the cable and the pulling force maximum without cable.
Q/ In the equilibrium position shown in figure below, the uniform bar (AB) has a mass of (50 kg) and supports load (200 kg) at (A). Determine the tension (T) in the cable and reaction force at (B)? O 2.5m 2.5m 200 kg T = 6511 N, FBx = 3823 N, and FBy = : 8992 N T = 7646 N, FBx = 3823 N, and FBy = 4169 N T = 7646 N, FBx= 2000 N, and FBy = 3299 N O Non of the above
The cable of a suspension bridge supports half of the uniform roadsurface between the two towers at A and B, shown. If this distributed loading is w0, determine the maximum force developed in the cable and the cable’s required length. The span length L and sag h are known.
The ball D has a mass of 30kg. If a force F= 120N is applied horizontally to the ring at A, determine the largest dimension d so that the force in cable AC is zero.
2, The rigid body ABC is held in place by ball and socket joints at A and C, and cable DE which passes through the right at point B. Find the tension in Cable DE. The coordinates of the points in (mm) are as follow: A, (0,0,600) B, (600,0,600) C, (800,0,0) D, (0,500,300) E, ( 800,500,0) F, (800,0,600)
4. For the beam and loading shown, determine the tension in the cable and the support reactions at hinge A. Neglect the thickness of the beam and the size and friction of the pulley at E. E 2 kipsft 3 ft 3 ft 2 ft 10 kips 5. Find the maximum weight of the bucket that the wire system can support so that no single wire develops a tension more than 500 N. 3/3 25° 1300 300
3. The cable BC carries a tension of 800 N. Write this tension as a force T acting on point B in terms of the unit vectors i, j, and k. The elbow at A forms a right angle. 0.7 m 1.2 m- 1.6 m 30° B 0.8 m -X
PROBLEM 1: The 1500-kg beam ABC has fixed support at A and connected to beam BD by hinge at B. Beam BD has a mass of 2000 kg and supported by a cable at D. The cable is attached to the 20-cm-diameter pulley at E and pulled vertically at the other end, by tension T. Given: a = 1.5 m; b = 0.9 m; c = 1.8 m d = 0.6 m; e = 1.4 m; θ = 75°. 1. Calculate the required tension to maintain in equilibrium. (ANSWER: 12.830KN) 2. Calculate the moment reaction at A (ANSWER: 28.499) and the total reaction at A. (ANSWER: 22.192). 3. Calculate the vertical reaction at E. (ANSWER: 25.223)
1. The motor draws in the cable with an acceleration ap of 3 m/s² (upward). Determine the reactions at the supports A and B. The beam has a uniform mass of 30 kg/m, and the crate has a mass of 200 kg. Neglect the mass of the motor and pulleys. 2.5 m 0.5 m ++ ap↑ с 3.0 m
P3/4 6. The two blocks are placed on the inclined with the cable taut. Determine the force P required to initiate motion of the 15 kg block if P is applied down the inclined. H₂=0.3 8 kg H₁ = 0.25 15 kg P 25⁰
The 970-kg motorized unit A is designed to raise and lower the 435-kg bucket B of concrete. Determine the average force R which supports unit A during the 5.2 seconds required to slow the descent of the bucket from 3.3 m/s to 0.4 m/s. Analyze the entire system as a unit without finding the tension in the cable. B. Answer: R= i kN