. The following picture shows a LONG conductor carrying current I. Nearby there is aconducting rectangular loop with sides a = 8 cm and b = 4 cm. The loop also carries aresistance R = 10 ohms. The curent is constant and has a value of I = 6.0 Amperes. Theloop is moving away to the right with a constant velocity, V = 2 m/s. Answer the followingquestions at the instant of time t" when the left edge of the loop is at position "x" as shownbelowUse the coordinate system , x to the right, y into the board, z upwarda) Write an expression for the magnetic field as a function ofthe distance "x" (from the LONG conductor to the loop. )USE “+" for CCW circulation and "-“ for CW circulation.b) Write the magnetic field in "i-j-k" format at point "x" to theright of the current carying wire in the "-z" planeRc) Write the infinitesimal area vector for the loop in "i-j-k"formatd) Write the explicit integral for the magnetic flux through thearea of the loop using the answer for B and dA above.Include limits on the area integral In generale) Integrate the flux integral above to obtain„(x) = "Ho`I-a[in(x+b) – In(x)]f) Express the position "x" as a function of "g) Show the time rate of change in the magnetic flux isdo„(x) _ _Ho·I•a ·b•V[_dt(q + x) . xh) Use Faradays Law to determine the induced EMF at x = 3cmi) Use Ohms Law to detemine the current in the loop when x = 3cmi) Use Lenz's Law to determine which direction does the current flow? (Clock Wise or CounterClock Wise). Explain.NOTE: Lenz's Law says the direction of the induced current will create a magnetic field tooppose the original change in the magnetic flux. That is, if the original magnetic flux throughthe loop is increasing, the direction of the INDUCED magnetic field is opposite the originalmagnetic field. Similarly, if the original magnetic flux through the loop is decreasing, thedirection of the INDUCED magnetic field is in the same direction the original magnetic field.)

The expression for a magnetic field at a distance x due to a straight conductor carrying a current I…

Answered: The following picture shows a LONG…

Similar questions

7. Consider two semi-infinite wires connected with a 4 circular bend and current i flowing as shown. Using an appropriate combination of the Biot-Savart Law dB = Hoi dĩ x ê Ampere's Law 4n r² PB• ds = H, ime > superposition, and symmetry to calculate B at point P as indicated. Note: You must correctly support each step and explain exactly what assumptions you are making. R
For the circuit shown below, Ɛ = 24 V, L = 3.6 mH, and R = 3.0 N. After steady state is reached with S, closed and S, open, S, is closed and immediately thereafter (at t = 0) S, is opened. R S2 R (a) Determine the current through L (in A) at t = 0. A (b) Determine the current through L (in A) at t = 4.0 x 10-4 s. A (c) Determine the voltages across L and R (in V) at t = 4.0 x 10-4 s. V, = V VR = V 0000,
(a) The figure below shows two parallel conducting rails 15.2 cm apart, connected by a resistor with resistance R₂ = 5.00 Q. Two metal rods with resistances R₁ = 11.40 and R₂ = 15.0 (2 slide along the rails with negligible friction. Rod R₁ slides to the left at constant speed v₁ = 4.00 m/s, while rod R₂ slides at speed v₂ = 2.00 m/s. The rods and rails are in the presence of a uniform magnetic field pointing into the page, perpendicular to the plane of the rails, with a magnitude of Bin = 0.0100 T. +5 x x x x x x x x x x x x x x x x x x x x x x x x x x upward x x x ---Select--- X * x x x x x x x x Rg x x x x x R₁ R₂ What are the magnitude (in μA) and direction of the current through resistor R₂? μA magnitude direction x x x x (b) What If? What are the magnitude (in μA) and direction of the current through resistor R. if the rods move inward, instead of outward, with the same speeds as in part (a)? μA magnitude direction
Time t < 0, the circuit is in DC Steady State. The switch is opened instantly at time t=0. This question deals with the new initial conditions for t>0. When t<0, I₂ = 7 A, and I₃ = 9 A. Give I₂ at t=0+ (at t=0, but after the switch is opened).
I 3 a ↑ R1 $220 R2 330 R3 390 I2 I3 vi 12V A * В Calculations: Node Equα tion: Σ I i-ΣΙ out 11 + 12 = 13 Loop Equation: Loop 1: – 11(R1) + 12(R2) – V1 = 0 Loop 2:
To ignite a mixture of gasoline and air inside an internal combustion engine--like in your car--a spark is generated by a high voltage across the spark plug, usually in the 10's of thousands of volts, but the battery is only 12 V. This massive increase in voltage is achieved through a transformer called the 'ignition coil'. A typical ignition coil has a primary with 300 turns wrapped around a radius of 2 cm over a linear distance of 15 cm. The secondary has 60,000 turns of wire over the same cylinder. The spark is generated when the current is suddenly shut off to the coil. Assuming that the magnetic field is uniform inside the primary and secondary coils, and that all of the magnetic field lines that go through the primary go through the secondary, what voltage is generated in the secondary coil if the current in the primary coil drops from 10 A to 0 A at a steady rate over the course of 50 mirco-seconds? Give your answer to 2 significant digits. Hint: Remember the definition of flux…
A cylindrical solenoid of length 0.711 m and radius 0.0334 m which carries a current of i = 4.06 A has a total stored energy of UB = 4460 J. How many turns per unit length does the solenoid have? i m-1
Two long parallel conducting rails are separated by a distance d. At one end they are joined by a resistance R. A conducting bar of length d is made to slide at constant velocity v along the rails. Both the bar and the rails have negligible resistance. (a) What current flows in the circuit? (b) How much power is required to move the bar? (C) How does the power dissipated in the resistance compare with the power required to move the bar?