The following information is given. Calculate the maximum cubic feet of storage that is needed to store 10,000 cases. • Case size = 2' (w) × 1.5' (1) × 2' (h) • Cases stacked 2 layers high per pallet Pallet size 3.33' (wide) x 4' (long) x 0.5' (high) Clearance between pallets = 0,5 • Space above each pallet for racking system -0.5 You will store items 2 racks high. Assume no honeycombing and 0.5' space necd all around the pallet %23 Round your answer to 2 decimal places. Select the closest answer to yaur calculation.

The following information is given. Calculate the maximum cubic feet of storage that is needed to store 10,000 cases. • Case size = 2' (w) × 1.5' (1) × 2' (h) • Cases stacked 2 layers high per pallet Pallet size 3.33' (wide) x 4' (long) x 0.5' (high) Clearance between pallets = 0,5 • Space above each pallet for racking system -0.5 You will store items 2 racks high. Assume no honeycombing and 0.5' space necd all around the pallet %23 Round your answer to 2 decimal places. Select the closest answer to yaur calculation.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Estimate the quantity and board foot of the studs used in a wall partition 5.80m long and 3.40m high. The studs are 2" x 3" and are spaced at 60cm O. C. both ways.
A tank containing liquid with SG = 1.78 was put on a weighing scale and registered a total weight of 84 kilograms. Obtain the new reading on the weighing scale (in kg.) if a 66 mm by 73 mm piece of wood is held vertically in the water to a depth of 591 mm. Round off to two decimal places.
6. Determine the number of pounds and kilograms of rebar required for a construction project with the following bar list: 700 No. 6–20 ft long 300 No. 5–8 ft long 400 No. 4–4 ft long
Give the following uses of each parts of Mohr's-Westphal Balance below. 1. Balancing adjuster 2. Gravity Nut 3. Beam 4. Thermometer 5. Platinum Wire 6. Plumb/Plummet 7. Glass Measuring 8. Riders/ Weights 9. Lock Screw 10. Adjustment Screw 11. Balancing adjuster 12. Bracket Also, the uses for each part of pycnometer. 1. Glass cover 2. Side tube 3. Glass bottle 4. Glass stopper 5. Capillary
A block of wood 0.6m x 0.6m x “h” meters in dimension was thrown into the water, if floatswith 0.18m. Projecting above the water surface. The same block was thrown into a container of a liquid having a sp.gr. Of 0.90 and it floats with 0.14m projecting above the liquid surface. A. Determine the value of “h”.B. Determine the sp.gr. of the block.C. Determine the weight of the block.
Hi, please provide clear and detailed solution as I will be studying them. Use up to three decimal places and draw+label diagrams. Thank you!
Urgent, need correct answer as soon as possible with complete solution. Box final answer in 4 decimal place. Thank you A tank with vertical sides is 1.20 m square, 3.0 m deep and is filled to a depth of 2.70 m with water. A cube of wood having a specific gravity of 0.50 measuring 60cm on an edge is placed in the water so that it will float. a. Find the weight of volume of water displaced. B. b. Determine the depth that the water will rise inside the tank from its original water level. c. what will be the change in pressure on the side of the tank?
Submit your question to our 24/7 subject matter experts with Masters and PhDs and get a solution in as fast as 30 minutes* Provide clear and step by step solution with illustration Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.
The "Quality Woods" factory is dedicated to the manufacture of doors. It is currently developing the "Classic 2050" style and requires you to conduct a process flow study. The information necessary for the construction of the DOP is presented below: The materials for making doors are sent from the raw material warehouse to the production department (1.40 mt, 0.51 min). An operator cuts the vertical posts (7 min), moves to planing (0.5 min; 1 mt); the vertical columns are brushed (8 min), it is moved to glued (1.4 mt, 0.51 min). At the same time as the vertical studs are cut, the horizontal studs are cut (10 min), the horizontal studs are planed (10 min). Once the horizontal columns are ready, they are transferred to gluing with vertical columns (1.2 mt, 0.55 min). Vertical uprights are glued to the horizontal ones using glue (15 min). Let it dry in a separate area (15 min). An operator checks that the uprights are well glued and proceeds to nail (6 min), then is transferred to gluing…
To repair a certain refrigerator, these lengths of wire are needed: 6 feet 4inches, 2 feet 3 inches, 1 foot 11 inches, and 4 feet 9 inches. The lengths arecut from a 25-foot coil. Find in feet and inches the amount of coil left after thelengths are cut.
A closet measures 2.5 m by 1.2 m by 2 m. What is the storage capacity of the closet?
DESIGN DESCRIPTION To construct a warehouse, the frame system shown in Figure 1 has been adopted. As an engineer, your task is to analyse the mid frame, highlighted in RED. Column 3 Column 1 Beam 1 Columb 2 Slab 1 Beam 1 Slab 2 Beam 2 Beam 3 Column 2 5 m 5 m 5 m Column 3 Column 1 8 m (a) Transfer of self-weight of Slabs 1 and 2 to surrounding beams (simplified case) Beam 1 Figure 1 A warehouse frame system The detailed information of the structural components is provided as follows: Slabs 1 and 2 are made of in-situ cast reinforced concrete and have a thickness of 150 mm (Figure 2). For simplicity, we assume that half the weight of each slab is transferred to Beam 1 (as shown in Figure 2). In addition, a water tank full of water with a weight of 1042 kg (1000 L of water plus weight of the tank) will be installed in the middle of Beam 1 (Figure 2). All the beams are made of reinforced concrete and have a standard size of 225 mm x 600 mm. Note that the density of reinforced concrete is…