The flow rate through a 10-cm-diameter wrought iron pipe shown below is 0.04 m³/s. Find the difference in elevation H (meters) of the two reservoirs. Round off your answer to two decimal places. Take the loss coefficients Kentrance = 0.3, Kvalve = 7, Kelbow = 0.7, Kexit = 1.2. 1 Water 20°C Screwed globe valve (fully open) H 2

The flow rate through a 10-cm-diameter wrought iron pipe shown below is 0.04 m³/s. Find the difference in elevation H (meters) of the two reservoirs. Round off your answer to two decimal places. Take the loss coefficients Kentrance = 0.3, Kvalve = 7, Kelbow = 0.7, Kexit = 1.2. 1 Water 20°C Screwed globe valve (fully open) H 2

Name: The flow rate through a 10-cm-diameter wroughtiron pipe shown below i
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The flow rate through a 10-cm-diameter wroughtiron pipe shown below is 0.04 m³/s. Find thedifference in elevation H (meters) of the tworeservoirs. Round off your answer to two decimalplaces. Take the loss coefficients Kentrance = 0.3,Kvalve = 7, Kel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I want the method to calculate the Reynolds number, where did this number 435,000 come from(Marked in red) ? please very urgent
Please give a detailed Handwritten solution.
Examples & The Inlet to pump is 10.50m above the bottom of sump from which it draw water through a suction pipe. If the pressure at the pamp inlet is not to fall bellow 28 kN/m² absolute, work out the minimum depth of water in the tank 6.019 m O 15m 0 3.019 m O 9.019 m O 1.019 m O
7) A pump has the following characteristic: Volume flow rate 23 46 69 92 115 (m³/h) Head (m) 17 16 13.5 10.5 6.6 The is used to pump water from a lower tank to a higher tank through a total length of pump 800 m of 150 mm diameter pipe. The difference between the water levels in the two tanks is 8m. Neglecting all losses except friction and assuming that C; = 0.004, find the rate of flow between the two reservoirs. [Ans: = 60m/hr]
Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm diameter pipe, with a length of 250 m. A turbine is installed between the two reservoirs. The flow of water in the pipe is 140 L/s. Use C = 120. Use the equation of Hazen - Williams for head loss as, h₂ 10.67LQ1.85 C1.85 D4.87 Calculate the head loss. Determine the head extracted by the turbine. Find the power generated by the turbine.
i need the answer quickly
Q9
As shown in the figure below, a cylindrical tank with a hole in the bottom and an air vent in the top is being filled with water. Given the following: Dtank = 4 ft hill = 8 ft NOG height of water in tank when tank is filled Qin = 10 gal/min %3D NOT UPL TO CHE diameter of hole Find: volumetric flowrate into tank EGG EXAM into the tank in slugs/second OT UPS XAM O NOT U EXAM (c) The rate at which the water level in the tank is mass flowrate (in slugs/second) of the water (b) The mass flowrate (in slugs/second) out of the tank UPLOAD TO CHE NOT UPLOAD when the water level reaches the fill height DO NOT UPL rising (in inches/minute) when the water level NOT UPL PLOAD TO CHEGG NOT UPLOAD TO CHEGG EXAM TO CHEGG EXAM OD TO CHEGG UP reaches the filled height то снE LOAD vent Dtank DO DO DO NOT UPLOADTO EXAM EX DO 0 DONOT UPLOA T Dhole G EXAM TO CNGO UPLOA hole mdotout
1.Find the diameter of a pipe of length 3000 m when the rate of flow of water through the pipe is 300 litres/s and the head lost due to friction is 5 m. Take the value of C = 50 in Chezy’s formula.
Water is discharged from a reservoir into the atmosphere through a 80 m long pipe. There is a sharp entrance to the pipe and the diameter is 250 mm for the first 50 m. The outlet is 35 m below the surface level in the reservoir. The pipe then enlarges suddenly to 450 mm in diameter for the reminder of its length. Take f 0.004 for both pipes. Calculate the discharge.
Q5
Please show complete work in a sheet of paper. Will appreciate