Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm diameter pipe, with a length of 250 m. A turbine is installed between the two reservoirs. The flow of water in the pipe is 140 L/s. Use C = 120. Use the equation of Hazen - Williams for head loss as, h₂ 10.67LQ1.85 C1.85 D4.87 • Calculate the head loss. • Determine the head extracted by the turbine. Find the power generated by the turbine. •

Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm diameter pipe, with a length of 250 m. A turbine is installed between the two reservoirs. The flow of water in the pipe is 140 L/s. Use C = 120. Use the equation of Hazen - Williams for head loss as, h₂ 10.67LQ1.85 C1.85 D4.87 • Calculate the head loss. • Determine the head extracted by the turbine. Find the power generated by the turbine. •

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1) Determine the Pressure and Velocity head at each point. Find the exiting flowrate. Point 1 2 3 4 5 6 Kent=1 Pressure Head Pipe 1 Kbend-0.2 Kexp=0.3 Velocity Head Kval=2.2 Elevation Head 70 62 50 48 45 43 4 Kbend-0.2 Kcont=0.1 Pipe 1 2 3 4 5 6 Kexit=1 Lm 250 150 150 170 100 200 D mm 150 150 300 300 300 150 f 0.022 0.022 0.02 0.02 0.02 0.022
If pipe 1 diameter = 55 mm, mean velocity 2 m/s, pipe 2 diameter = 40 mm, mean velocity 3.5 m/s, and pipe 3 diameter 90 mm. 3 then the discharge value Q1 is L/S 2
B7
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Fast pls i will give u like for sure solve this question correctly in 5 min pls A reduced bend in a pipe is used to divert the flow of water (p=1000 kg/m³) at a rate of 35 kg/s. The discharge of the fluid is to the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the outlet. The elevation difference between the centers of the exit and entrance is 40 cm. The mass of the cubit and the water it contains is 60 kg. The center of mass of the fluid assembly and elbow is located 50cm horizontally, with respect to the flange. Consider a flow correction factor of n=1.04 for eq. of linear momentum. Determine: a. The pressure at the entrance of the elbow. b. The net anchorage force in the flange required to hold the elbow in place. c. The moment generated in the flange from the applied forces
Q5
The head-discharge relationship for a certain pump can be represented by the equation H-29-6Q^2 The pump is fixed 2 m shove the water surface tank at a level 10 m above the pump. The suction and delivery pipes are 12 m and 720 m long, respectively and each pipe is 0.5 m in diameter. The Estimate the discharge (in m³/s) at the best operating point for the pumping system,