The figure shows a hydraulic platform for vehicles made up of two frames equal to the one shown. A 20.0 kN car, with the center of gravity at G, is supported in the position shown. Calculate: a) The force that the cylinder rod EF exerts on each of the members CD b) The horizontal and vertical components of the support reaction C -3,15 m- 1,4 m 0,5 m 1,0 m 0,3 m 0,25m 1,5 m 1,7 m 2,5m

The figure shows a hydraulic platform for vehicles made up of two frames equal to the one shown. A 20.0 kN car, with the center of gravity at G, is supported in the position shown. Calculate: a) The force that the cylinder rod EF exerts on each of the members CD b) The horizontal and vertical components of the support reaction C -3,15 m- 1,4 m 0,5 m 1,0 m 0,3 m 0,25m 1,5 m 1,7 m 2,5m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve asap
A load P is supported by a structure consisting of rigid bar ABC, two identical solid aluminum alloy [E = 73 GPa] rods (1), and a solid bronze [E = 105 GPa] rod (2). The aluminum rods (1) each have a diameter of 11 mm and a length of L1 = 1.5 m. They are symmetrically positioned relative to middle rod (2) and the applied load P. Bronze rod (2) has a diameter of 21 mm and a length of L2 = 0.8 m. If all bars are unstressed before the load P is applied, determine the normal stresses in the aluminum and bronze rods after a load of P = 76 kN is applied to the rigid bar.
The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown, determine the mass of the block at D. Give your answer in kg and to 3 significant figures. 3 m- 3 m www. KAC = 20 N/m -4 m- www wwwww B KAB = 30 N/m
Find roller support reaction
The jib crane is designed for a maximum capacity of 9 KN, and its uniform I-beam has a mass of 240 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.3 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 0.8 m? (b) What is the value of R when x = 3.5 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 9 KN 1.6 m Questions: (a) If x= 0.8 m, R = KN (b) If x= 3.5 m, R= i KN m (c) The minimum value for R = i (d) The pin should be designed to hold -2.9 m i kN at x = kN. i
The jib crane is designed for a maximum capacity of 6 kN, and its uniform I-beam has a mass of 190 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 3.8 m. On the same set of axes, plot the x- and y- components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (a) What is the value of R when x = 1.6 m? (b) What is the value of R when x = 3.3 m? (c) Determine the minimum value of R and the corresponding value of x. (d) For what value of R should the pin at A be designed? 39° x m 6 KN -2.5 m 1.5 m Questions: (a) If x= 1.6 m, R= (b) If x= 3.3 m, R = i (c) The minimum value for R = i (d) The pin should be designed to hold i KN KN kN at x = kN. i
calculate the reactions using static equilibrium Please show all steps + FBD You should use TwO FBDS! w = 1.0 kip/ft 14 ft 10 ft 45 deg D 24 ft
Problem 1 A beam is supported as shown below: A B D F Hinge Hinge 5 m 5 m 6 m 3 m 3 m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: LOAD W(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) 20 25 40 Using influence line diagrams, determine the following: 4. Maximum moment reaction at F, MF in kN-m. (
Determine Static indeterminacy and also Find support reaction 20 kN 20 kN 4 kN/m 1 m. 1 m 1 m
question 1..
WA 4-m bar of negligible weight rests in a horizontal position on the smooth planes shown in the Figure, if T = 30 KN and x = 1 m. Determine the Reaction at A. 1m P = 20 kN 30° 45° 4 m 16.82 KN None of the above O 44.83 KN O 25.89 KN 36.60 KN