VPThe figure (not drawn to scale) shows a metallic cylindricalcolumn submitted to a combined load: bending and torsion. Thecolumn contains an hemispherical groove of radius r, located at adistance L from the point of application of the loads.You are giventhe column diameter D = 68 mm,the groove radius r = 6 mm,the distance L= 200 mm,the bending load P=5 kN,and the torque T = 600 N.m.The material data areYoung's modulus E = 122 GPaShear Modulus G = 55 GPaPoisson's ratio v = 0.1and Yield strength oy = 380 MPa.a) Write a numbered list of the calculation steps required toobtain the factor of safety in yielding based on the maximumdistortion energy (Von Mises) criterion.Enter your answer in the box below b) Calculate the factor of safety in yielding based on themaximum energy (Von Mises) criterion.The answer is acceptable within a tolerance of .1Answers out of this +/-0.1 tolerance, but within a 10% tolerancewill score 8 marksNote that the F.O.S can be lower than 1 in this question.

Answered: Image /qna-images/answer/a4ef49de-cebd-4254-9ef5-4caca3c2539e.jpg

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Find the reactions for the supports on the frame below. P is 24 kN the y direction, F is 12 kN in…

Q: The L-bar shown in the figure is fastened by a bearing at point A that allows it to rotate, such…

A: Given F=800NRBmax=600N

Q: Please solve it using a free body diagram. Show all the components. Don't use chatgpt,Only…

A: thank you

Q: Draw and label a complete FBD of each beam Solve for the reaction forces (support forces) for each…

A: The free-body diagram of the given loading beam can be drawn as below, Here, RAy is the vertical…

Q: 4- Şekildeki mekanizma ile E ucundaki tahta sıkıştırılacaktır. Buna göre uygulanan düşey P kol…

Q: Find the reactions for the supports on the frame below. P is 12 kN in the x direction, F is 24 kN in…

Q: The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load:…

Q: 4-3.18. Repeat Prob. 4-3.17 if the loads Q are zero and each load P = 2000 lb.

Q: The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional…

Q: The rigid arm of negligible weight shown in the figure supports a load of F = 852 N. The chains are…

A: Given data: F=852 Nx1=5 mx2=4 my=7 mz=5 m Need to determine the Magnitude of the force in FBE.

Q: e the resultant amplitude of stress. e the resultant mean stress

A: Given that , D= 300 mm Torque τ can be calculated as , =( F1 -F2 )× D2=1769-398×320=205.6 N-m…

Q: The BC rod, which is assumed to be rigid and massless in Figure, stands horizontally with the help…

A: Draw the deflection diagram. From the deflection diagram, the relation between deflections is,

Q: The vertical structure ABCD shown in Figure 1(a) is subjected to a system of coplanar forces and a…

Q: A floor hoist supports an engine of weight WE 2.9 kN. As illustrated in the figure below, the floor…

Q: A bent pipe is attached to a wall with brackets as shown. A force of F= 235 lb is applied to the end…

A: Given data:Force, F = 235 lba = 12 inb = 27 inc = 20.3 ind = 75 inh = 42.5 ing = 50 inAssume D is…

Q: Determine the internal forces at point J for the structure shown, where member BD can only carry…

Q: 3) For the given plate subjected to two point forces, calculate the nodal displacements and the…

A: Step 1: Step 2: Step 3: Step 4:

Q: 1. A rod of length 1.50 m and diameter 0.12 m is mounted in a rigid wall A vertical bar of length…

A: INTRODUCTION : In order to solve the above problem, the maximum shear stress theory is applied when…

Q: on plane of L3 Co, 0.0)

Q: The Uniform AB brass bar is fixed with support and pin as shown in the figure and has a rectangular…

A: Given data: (a) Write the expression for the critical load in the horizontal direction.

Q: A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape…

Q: A sign ABCD is constructed from 7 mm thick plate steel (density p=8000 kg/m³) with the geometry…

A: To find:Determine the reaction forces at A and E. Given data:A sign ABCD is constructed from a steel…

Q: Problem 4-21: The rigid beam is supported at its ends by two A- 36 steel tie rods. If the allowable…

A: Given:The allowable stress of the steel, The load, The value of The length of the rods,

Q: The tractor shovel shown (Figure 4) carries a 530 kgkg load that has its center of mass at H. The…

A: The tractor shovel shown (Figure 4) carries a 530 kg load that has its center of mass at H.The…

Q: Consider the bracket shown in Fig-3. If: • F1 = 10 lb @ -90° • a - 2 ft • b = 4 ft C = 1 ft then,…

Q: Determine the equivalent nodal forces for the axially distributed loading acting on the bar…

A: Solution: Given Data: bx=96-6x lb/in To Find: f1 and f2

Q: 4 kN 3 kN 375 mm 375 mm B 750 mm As shown in the figure, the shaft is supported by bearings A and B…

A: Given data Material used A36 Diameter of the shaft = 50mm To determine the maximum theoretical…

Q: 75 lh 10 in. -10 in. for pin A and roller B for five different values of a Calculate reaction forces…

Q: MECHANICS OF DEFORMABLE BODIES 1. In the figure shown, the rigid bar with negligible mass was…

Q: The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: To Find : The load that act along members BE and FED. Given : The thickness of slab is t=200mm. The…

Q: Four wooden dowels with a diameter of 30mm are attached to a board. Two ropes pass around the…

A: Given data Diameter = 30mm Force P= 110N and Q= 189N Find the resulting torque

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A: Draw the free-body diagram of the frame.

Q: Calculate the displacements at nodes 1 and 2, the reactions at nodes 1 and 3, as well as the axial…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The rigid bars shown are separated by a roller at Cand pinned at A and D. A steel rod at B helps…

Q: The space truss above is supported by ball-and-socket joint at points A, B, and E. A single force F…

Q: For the figure shown below. Determine the force exerted on the bar ABC by the cylinder with a mass…

A: The FBD is given below -

Q: Determine the nodal displacements the forces in each element and the reactions.Use the direct…

A: GivenE1=30×106PsiE2=15×106PsiA=5in2L2=L1=30in

Q: Determine the reaction components at the roller support at B and the hinge support at C due to the…

Q: (b) The steel shaft has a diameter of 40 mm and is fixed at its ends A and B as shown in Figure…

Q: Find the reactions for the supports on the frame below. P is 24 kN in the y direction, F is 12 kN in…

A: Given:

Q: Figure P2 shows a frame structure that is used to support a 500 N load. Determine: 1) The reactions…

Q: M C a In the figure above, g = 3, f = 7, d = 7.616, a = 5.2m, b 3 2.2m, с — 1.2т and @ — 28° A…

Q: A load weighing P kN with AB, AC and AD cables such as are carried. Points A and B are x-axis, C and…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

VP
The figure (not drawn to scale) shows a metallic cylindrical
column submitted to a combined load: bending and torsion. The
column contains an hemispherical groove of radius r, located at a
distance L from the point of application of the loads.
You are given
the column diameter D = 68 mm,
the groove radius r = 6 mm,
the distance L= 200 mm,
the bending load P=5 kN,
and the torque T = 600 N.m.
The material data are
Young's modulus E = 122 GPa
Shear Modulus G = 55 GPa
Poisson's ratio v = 0.1
and Yield strength oy = 380 MPa.
a) Write a numbered list of the calculation steps required to
obtain the factor of safety in yielding based on the maximum
distortion energy (Von Mises) criterion.
Enter your answer in the box below

b) Calculate the factor of safety in yielding based on the
maximum energy (Von Mises) criterion.
The answer is acceptable within a tolerance of .1
Answers out of this +/-0.1 tolerance, but within a 10% tolerance
will score 8 marks
Note that the F.O.S can be lower than 1 in this question.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the frame shown in figure below, the rotation at (A) equals: * 60 kN.m A 1m I B I C 3m 200/EI O 160/EI O 180/EI O 240/EI
For the rhombodial frame shown, find the forces acting in Ac and AD
Gkuestrons T ØD VP The figure (not drawn to scale) shows a metallic cylindrical column submitted to a combined load: bending and torsion. The column contains an hemispherical groove of radius r, located at a distance L from the point of application of the loads. You are given the column diameter D = 68 mm, the groove radius r = 6 mm, the distance L= 200 mm, the bending load P=5 kN, and the torque T = 600 N.m. The material data are Young's modulus E = 122 GPa Shear Modulus G = 55 GPa Poisson's ratio v= 0.1 and Yield strength oy = 380 MPa. a) Write a numbered list of the calculation steps required to obtain the factor of safety in yielding based on the maximum distortion energy (Von Mises) criterion.
Determine the force in members BC, GA, and BG of the truss shown in the figure below. Let P = 175 kN. NOTE: If your answer is a compressive force then just put a negative sign. If your answer is a tensile force then just type the answer directly. (ALSO, DON'T FORGET THE UNITS) 2P 2P 30 60V60° B 60 60° 30 3P 4m 4m 4m Solve the force in member BC. Solve the force in member GA. Solve the force in member BG.
In the figure, torsional moments act on a bar system of abruptly changing cross-section made of the same material. Accordingly, calculate the value of the factor α so that the support responses are of the same magnitude in absolute value. What must the torsional moment=Mb be for the D-end to be zero? Note: The shear modulus of the material is G = 80 GPa Mo= 10 kNm.
Pravinbhai
I need the answer as soon as possible
Please draw a complete free body diagram including their components.
A flanged wooden shape is used to support the loads shown on the beam. The dimensions of the shape are shown in the second figure. Assume LAB = 8 ft. LBc=2 ft, LCD= 4 ft, LDE= 4 ft, Pc = 1850 lb, PE = 2160 lb, WAB = 830 lb/ft, b₁ = 10 in., b2= 2 in., b3 = 6 in., d₁ = 2 in., d₂= 11 in., d3 = 2 in. Consider the entire 18-ft length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. Answers: (a) σT = (b) a = WAB LAB i 545.779 706.391 B Pc LBC b₁ b3 C LCD -b₂ psi. psi. D ↓ d₁ LDE d₂ PE E