The figure below shows an inclined well-type manometer in which the distance L indicates the movement of the gage fluid level as the pressure PA is applied above the well. The gage fluid has a specific gravity of 0.85 and L = l25 mm. Neglecting the drop in fluid level in the well, Calculate PA

Q: A hydraulic jump is shown in figure below. The depth of flow z₂ after the hydraulic jump is 5 m…

A: Depth, Z1 = 6 mDepth after the hydraulic jump, Z = 5 mLength, l = 0.4 mFlow rate, Q = 450…

Q: A pressure measurement apparatus without leakage and friction between piston and cylinder wall is…

A:

Q: Problem 2 The containers A and B, shown on the figure, are filled HO with water, with density Pwater…

A:

Q: 2. Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on…

A:

Q: HYDROSTATIC FORCE ON PLANE SURFACE I need help analyzing my experiment. Between the measured and…

A: Data given

Q: An oil of specific gravity 0.85 is flowing through an inclined venturimeter fitted to a 250mm…

A: Given : Specific gravity of oil = 0.85 Dia of pipe = 250 mm Qoil= 110 lit/s  Inclination of…

Q: 5. A finite difference flow model well. Is the model-predicted head likely to be higher or lower…

A: To determine flow rates, flow direction, and hydraulic heads through an aquifer, the finite…

Q: erted manometers used Date: pi pe - Find the pressure difference of K Fluid x (s.g- 0.9) 0.5 m

A:

Q: need the answer

A:

Q: For the shown inverted manometer, all fluids are at 20°C. If P - P = 97 kPa, what must the height X…

A: Using concept of Pressure in left limb of manometer = pressure in right limb  solution = 1.31m

Q: fluids shown in the figure are at 20°C. If V₁ = 2.6 ft/s and losses are neglected, determine the…

A: This question is related to the Fluid Mechanics from Civil Engineering. Given Data -  V1 = 2.6…

Q: A pipe conveys water with velocity 360 m/min and pressure gauge shows 5 bar pressure under which the…

A:

Q: A differential manometer is attached to a pipe as shown. Determine the pressure difference between…

A: 2 rules :- 1. Pressure in a liquid at a particular level is same everywhere. 2. There is increase in…

Q: In the figure below, a fluid with a specific gravity of 0.77 is flowing. The mass flow rate is…

A: Given data,  Specific gravity = 0.77 Mass flow rate = 18.5  kg /s Diameter of nozzle = 4.87 cm θ =…

Q: 6.8 in PA Water FIGUD

A:

Q: For the shown inverted manometer, all fluids are at 20°C. If P, - P, = 130 kPa, what must the height…

A:

Q: 4. If viscous effects are neglected and the tank is large, determine the flowrate from the tank…

A:

Q: Please help with solving

A:

Q: For the system shown in the figure below, obtain the pipe discharge values as well as the node…

A: Let the friction factor for all pipes is fhead loss due to friction between node 2 to 6 is…

Q: An inverted U-tube of the form shown in Fig. 2.18 is used to measure the pressure difference between…

A: Determine the pressure difference between B and A point.a. If manometer is filled with air. b. If…

Q: The data in below table were obtained in a pressure build-up test on an oil well producing above the…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A fluid flows downward with the rate of Q=0.015 m/s in a smooth vertical pipe with the length of l.…

A: Given Data: The rate of flow of fluid is, Q=0.015 m3/s The initial guess is, f=0.02 The density of a…

Q: The table below show data collected from flow rate measurement experiment that was carried out using…

A: We will divide volume by time to calculate discharge.

Q: Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to release…

A: Estimate the velocity at point 2,V2=?

Q: SITUATION 4. AN OIL WITH SG = 0.86 FLOWS THROUGH A PIPE 30in. IN DIAMETER AT 700gpm 5. Determine the…

A:

Q: Prob-7 Density of gauge fluid used in well manometer is p =8000±10.0 Kg/m³. The maximum height of…

A: Density (ρ) = 8000 ± 10.0 Kg/m3 (0.125%) Maximum Height of reading scale H =0.8m ± 0.2 mm (0.025%)…

Q: For the following inverted manometer setup, if the pressure at x is 200 kPa, what is the pressure at…

A:

Q: a. discharge of pipe A b. discharge of pipe C c. discharge of pipe D

A:

Q: Figure shows below a Fluid 1 (SG = 0.88) and fluid 2 (SG = 2.93). If Pa = 98 kPa, determine the…

A:

Q: Estimate the velocity at point (2) and discharge of oil that as a petroleum engineer want to release…

A: Take point 2 as datumPressure at point 1, P1=100KPaPressure at point 2, P2=100KPaThe diameter of…

Q: meter consists of 8-mm diameter cylinder of length 20cm nd the mass of the sphere is 12.80g. At what…

A:

Q: b) Two pipes (at points A and B) have been connected with the manometer as shown in Figure Q1. i)…

A:

Q: Solve the following problems 1. With 30 liters/sec of water flowing as shown in figure, what…

A:

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.