The figure below shows a Yo-Yo of mass m =453 g which has an axle of radius r=1.2 cm and a spool of radius R= 2.0 cm. The Yo-Yo is placed upright on a horizontal plane. The string is pulled with a horizontal force Fas shown in the figure. What is the maximum magnitude of the pulling force, F, for which the Yo-Yo will roll without slipping? The coefficient of static friction between the Yo-Yo and the horizontal plane is u=0.6 and the moment of inertia of the Yo-Yo about an axis passing through its center is = (1/2)mR. Select one: 2663.64 N 3.63 N -39.95 N 4439 40 N

The figure below shows a Yo-Yo of mass m =453 g which has an axle of radius r=1.2 cm and a spool of radius R= 2.0 cm. The Yo-Yo is placed upright on a horizontal plane. The string is pulled with a horizontal force Fas shown in the figure. What is the maximum magnitude of the pulling force, F, for which the Yo-Yo will roll without slipping? The coefficient of static friction between the Yo-Yo and the horizontal plane is u=0.6 and the moment of inertia of the Yo-Yo about an axis passing through its center is = (1/2)mR. Select one: 2663.64 N 3.63 N -39.95 N 4439 40 N

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter10: Fixed-axis Rotation

Section: Chapter Questions

Problem 19CQ: What three factors affect the torque created by a force relative to a specific pivot point?

See similar textbooks

Similar questions

A boy rides his bicycle 2.00 km. The wheels have radius 30.0 cm. What is the total angle the tires rotate through during his trip?
What three factors affect the torque created by a force relative to a specific pivot point?
The arm of a crane at a construction site is17.0 m long, and it makes an angle of 16.8◦with the horizontal. Assume that the maximum load the crane can handle is limitedby the amount of torque the load producesaround the base of the arm.What maximum torque can the crane withstand if the maximum load the crane canhandle is 785 N?Answer in units of N · m.
The wheel of a car has a radius of 0.300 m. The engine ofthe car applies a torque of 240 N*m to this wheel, which does not slip against the road surface. Since the wheel does not slip, the road must be applying a force of static friction to the wheel that produces a counter torque. Moreever, the car has a constatnt velocity, so this counter torque balances the applied tourque. What is the magnitude of the static frictional force?
A horizontal force of 12.5 N is applied at an angle of 35.0 degrees to the door knob of a 75.0 cm door. What torque is produced to open the door? Give answer in N-m.
find torque.. only typing
A horizontal plate OAB of a triangular shape is pivoted at point O. Three forces act on the plate as shown in the figure. Fl = 6.O N, F2 = 8.0 N, and F3 = 7.0 N. F2 is perpendicular to OB. Find the net torque (in N.m) about the vertical axis passing through point O (Consider the counterclockwise sense as positive). 30° A 1.00 m 0.60 m B 1 45°/0 0.80 m
A stone is suspended from the free end of a wire that is wrapped aroundthe outer of a pulley as shown. The pulley is a solid cylinder with mass 10.0 kgand radius 30.0 cm. You measure that the stone travels 12.6 m in the first 3.00s starting from rest. What is (a) the tension in the wire and (b) the mass of thestone?
A uniform drawbridge must be held at a 37° angle abovethe horizontal to allow ships to pass underneath. The drawbridge weighs45,000 N and is 14.0 m long. A cable is connected 3.5 m from thehinge where the bridge pivots (measured along the bridge) and pullshorizontally on the bridge to hold it in place. What is the angular speed of the drawbridge as it becomes horizontal?
When tightening a bolt, you push perpendicularly on a wrench with a force of 167 N at a distance of 0.140 m from the center of the bolt. (a) How much torque are you exerting in newtons x meters (relative to the center of the bolt)? N. m (b) Convert this torque to footpounds. ft · Ib
with explanation pls.
Q3