The figure above shows a rope with a weight of 7 N / m which is suspended between points A and B. Point B is 10 m lower than point A. The arrow height in the middle between points A and B is 12 ma. Calculate the tension in the rope at A and at B. b. Calculate the rope length from point A to point B (Detailed answer for A 10 m B 70 m

The figure above shows a rope with a weight of 7 N / m which is suspended between points A and B. Point B is 10 m lower than point A. The arrow height in the middle between points A and B is 12 ma. Calculate the tension in the rope at A and at B. b. Calculate the rope length from point A to point B (Detailed answer for A 10 m B 70 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: to lower weights into the sea (density wn in the given figure. Determine the te 99.83 cm concrete…

Q: A kettlebell with a mass of 10 kg is suspended by three cables as shown in the figure and parameter…

A: A ball of mass 10kg is suspended at B.The is supported by 3 cables AB, BC, BD.To determine the…

Q: The climber A suspended from the rope weighs 75 kg as shown in the figure below. Determine the force…

Q: tunnel odel of an airplane wing is suspended as shown in the figure. What is the reaction in cable B…

A: Consider the given data L=43.8 lbD=3.42 lbM=0.6 in-lb

Q: Player 001 decided to create a 2-kg hanging figurine display as shown. The display is held in…

Q: For the beam section in Figure Q2 below, calculate the second moment of area along the X-axis (Icx).…

A: We have to find the reaction at support by using concept of equilibrium in first part of question.…

Q: As shown in the above diagram, rope and pulley system is used to support a load W with a mass of 350…

A: take g=10 m/s2f=w=mg=350*10=3500N

Q: 17. A 50-m steel tape is of standard length under a pull of 5.5 kg when supported throughout its…

A: Given data:- Standard Pull, Po = 5.5 kg Pull applied during the measurement, P = 8 kg…

Q: Can you help me with this, please show complete clear solution A barge is pulled by 2 tugboats. If…

A: Given data, Resultant force = 3800 lb Angle at A = 36° Angle of B = 26° To find out the tension…

Q: Rope 2 Rope 1 1300 100 N

A: Resolving 100 N force , we get 100cos30°=86.60N( in positive x direction)100sin30°=50N(in negative x…

Q: In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a…

A: we have to determine the value of maximum weight of the body according to the given data like we can…

Q: If the cables as shown in the figure below are holding the cylinder container, find its maximum…

Q: d as shown to the axle of pulley Knowing that the coefficient of static friction is 0.45, determine…

A: We have relation:T2=T1eμβμ=0.45β=κso,T2=T1e0.45πT2=4.1112T1

Q: There is a rope with a height difference of 4 m between the left and right hinge points, and is…

Q: d) The rope is cut and the sphere is allowed to float. What is the magnitude of the acceleration of…

Q: 5. A transmission tower is held by three guy wires attached to a pin at A and anchored by bolts at…

A: Given TAB = 110 lb

Q: Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B.…

A: (a) value of LAB and LBC From Fig LABcosα+LBCcosγ=hLABcos30+LBCcos60=23LAB+LBC=4 LBC=4-3LAB…

Q: A 75-Kg man wants to pull a 145- Kg b nd the ground is us = 0.3, while the co he ground is u, = 0.4.…

Q: A hot air balloon is tethered to the ground with three cables as shown in the figure. If the balloon…

A: Given data Find tension in cable BO.

Q: The two carts shown in the figure are attached with a pulley system. The friction in the system is…

A: Consider the pully:T'=2T........1

Q: 5 ft.

Q: An 80.0 kg constructor worker sits down 2.00 m from the end of a 1460 kg horizontal steel beam to…

A: Step 1

Q: A rope ABCD is looped over two pipes as shown. Knowing that the coefficient of static friction is…

Q: PRACTICE ANOTHER As shown below, a sign weighing 186 N is hanging (via a wire) from a uniform 344 N…

Q: 3. A 50 m tape was standardized and found to be 0.0015 m longer at an observed temperature of 31.5°C…

A: As per metioned above, I have solved question no. 3 Appreciate if there is detailed work with…

Q: -120m- 20m

Q: A rope ABCS is looped over two pipes as shown. Knowing that the coefficient of static friction is…

A: Given data, Coefficient of static friction μs=0.25

Q: A 5kg block has a rope of mass 2kg attached to its underside and a 3kg block is suspended from the…

A: Given:- A 5 kg block has a rope of mass 2 kg attached to its underside and a 3 kg block is suspended…

Q: 7.) Find the tension in each cord in the figure below. if the weight W of the suspended body is 150…

A: Determine the tension in each chord.

Q: A 804.4N horizontal steel shaft is suspended by a vertical cable from A and by a second cable BC…

A: Given:- The weight of the horizontal steel shaft = 804.4 N The horizontal steel shaft is suspended…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

The figure above shows a rope with a
weight of 7 N/ m which is suspended
between points A and B. Point B is 10 m
lower than point A. The arrow height in
the middle between points A and B is 12
ma. Calculate the tension in the rope at A
and at B. b. Calculate the rope length from
point A to point B
(Detailed answer for
A
10 m
B
70 m
十

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rigid bar AD is hanged by two steel cables of diameter 0.065 in as shown in the figure. Find: a) The tension force in the cable BE and cable CF when P=220 lb b) The deflection at Point D (6) Est=29*106 Psi F S in E 10 in A B 12 in 12 in 12 in
Please do it in 20 minutes. i'll give you thumbs up………
Give me right solution From the figure shown, block A weighs 400N and the coefficient of friction between block and the inclined plane is 0.20. Compute the following a) the tension of cable supporting block A if it will have an acceleration of 1.2 m/s2 up the plane. B) the the tension of the cable supporting block B. C) the weight of block B
The turnbuckle shown in Figure has a square thread with a mean radius of 5 mm and a lead of 2 mm. If the coefficient of static friction between the screw and the turnbuckle is 0.25, determine the moment M that must be applied to draw the end screws closer together. Choices: A. 6.36 N-m B. 7.36 N-m
A 50 m tape weighing 0.049 kg/m with a cross-sectional area of 0.05 sq. cm and modulus of elasticity equal to 2x106 kg/cm2 is used in determining the distances between two points. The tape is of standard length under a pull of 6.70 kg and a temperature of 25°C when supported throughout its entire length. The tape was then used in the field to measure a distance that was determined to be 378.123 m. At the time the measurement was made, the constant pull applied was 9 kg with the tape supported only at endpoints. During the measurement the recorded temperature was 17°C. Use o=11.6x10-6/C. Determine the correct length (in feet)of the line. Youranswer
Show complete solution and 3 decimal places for the final answer asap thank you!
Q2) Figure 2 shows a rope that is stretched between points A and C, there is mass m at point B. Given values: m= 20 kg, h= 2 m, d- 3 m, a= 30°, y-60°. Determine the followings: a) What are the values of lengths LAB and LBc must be selected according to the given angles a and y? b) What are the values of forces FAB and Fgsc in the rope sections AB and BC? A AB h B. Figure 2
Climber A is suspended from the rope weighs 75 kg as shown in the figure below. Determine the force in the rope connecting A and B.
6. Ropes AB and AC are thrown to a boater whose canoe has capsized. If a = 25° and the magnitude of the force FR exerted by the flowing water on the boater is 70. lb, determine a. the tension in rope AB b. the tension in rope AC B af 40⁰ FR 10⁰