A crane is used to lower weights into the sea (density=1020.81 kg/m3) for an underwater constructionproject, as shown in the given figure. Determine the tension in the rope of the crane due to a rectangular37.35x37.94x299.83 cm3 concrete block (density=2121.45 kg/m3) when it is completely immersed inwater.FT.waterWater(the force unit should be in (kN) and use one number after the docimaL Y00

Answered: Image /qna-images/answer/01de91cf-f7e6-4774-8485-8270608601ef.jpg

Answered: to lower weights into the sea (density…

Engineering

Civil Engineering

to lower weights into the sea (density wn in the given figure. Determine the te 99.83 cm concrete block (density=21

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the elastic shortening loss of a pretensioned prestressed concrete (simply supported L=15m, H=900mm, B=300mm) given that, fpi=1100MPa, f'ci=40MPa, Eps=200GPa, and the total area of the straight profile tendons is 140 sq mm. Provide the answer in percentage.
Problem 8.26 WD = 20 kN/m wj. = 36 kN/m 4 m concrete cover is 40 mm 6 #29 450 450 mm 70 mm 800 mm 730 mm For each of the problems, you must perform the following Recalculate the effective depth assuming concrete cover of 40 mm, and use only your calculated effective depth to answer the questions. Shear strength of concrete must be calculated using both the simplified and detailed methods of ACI318 Table 22.5.5.1. -Verity the spacing between main reinforcing bars satisfies AC1318 minimum spacing requirements. -Demonstrate the calculation of the shear forces needed to answer the questions including a fully labelled shear force diagram. The diagram must show the location within the span where 1) no shear force is required (if any), 2) minimum shear force is required (if any). Sketch (manual sketches OK) the beam and show the main reinforcement and distribution of shear reinforcement along the span, including distances where each spacing applies.
2) The flooring system shown is composed of slab panels measuring 20 X 25 ft in plan, supported by shallow column-line beams, as shown in the figure. The slab is pre-cast and resting on the beams. The panels carry a service live load of 144 psf in addition to the self-weight of the floor. a) Calculate the factored load on beam CD as per the tributary area shown. Assume a slab thickness of 7 in and the density of the concrete used to be 150 pcf. Use the load combinations from the ASCE 7-10 load combinations for Strength Design (2.3.2). b) Sketch the bending moment diagram (BMD) for the beam using the factored load calculated in step (a). c) Calculate Mu for the trapezoidal load distribution. d) Design a reinforced concrete beam using a rectangular section to carry the Mu calculated in step (c). You can use design guides, but show clear steps. Use concrete with fc'=4000 psi and steel with fy = 60000 psi.
The submerged brick is balanced by a 3kg mass on the beam scale. What is the specific weight of the brick if it displaced 3 liters of water?
Q.2 If the (010×10) cylinder compressive strength of O.P.C. concrete at 10-day is (14 MPa). Calculate (20×20×20) cube comp. strength at age of 28 days.
Subject reinforced concrete design solve p02
Please solve quickly, guess material
The approximate mass of a 75mm x 150mm concrete cylinder with an average concrete density of 2400 kg/m^3 is: A) 3.8 kg B) 7.6 kg C) 1.6 kg D) 3.2 kg
7. Does the density of concrete block exceed 1500 kg/m³?
Question 1: Consider a 600 mm deep reinforced concrete cantilever beam supported by a 600 mm square column as shown in the figure below. The beam reinforcement is anchored into the column. Minimum stirrups are provided in the anchorage zone according to CSA A23.3-19. Regular uncoated bars are used in the design. Material properties: fe= 35 MPa (normal-density concrete) and fy= 400 MPa. 1. Determine the largest beam rebar size that can be used without hook in this design according to the CSA A23.3 requirements. 2. Design the anchorage zone if the diameter of the longitudinal steel bars is 25 mm. 40 clear- 600 mm 40 clear 600 mm,
Reinforced Concrete