The extruded plastic shape has dimensions of D = 35 mm, d = 33 mm, a = 98 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 340 N. (b) If the allowable shear stress for the plastic material is 1400 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d a V Answer: (a) TA = kPa (b) V = N

The extruded plastic shape has dimensions of D = 35 mm, d = 33 mm, a = 98 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 340 N. (b) If the allowable shear stress for the plastic material is 1400 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d a V Answer: (a) TA = kPa (b) V = N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The extruded plastic shape has dimensions of D = 31 mm, d = 25 mm, a = 93 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1550 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d A a Answer: (a) TA = kPa (b) V =
The extruded plastic shape has dimensions of D = 20 mm, d = 14 mm, a = 92 mm, and t = 5 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 370 N. (b) If the allowable shear stress for the plastic material is 1300 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d a Answer: (a) TA = kPa (b) V = N.
Refer to the figure 1. Which of the following most nearly gives the value of the major principal stress? Answer: 216 kPA 2. Which of the following most nearly gives the value of the normal stress on the plane AB? Answer: 174.64 kPa 3. Which of the following gives the value of the shear stress on the plane AB? Answer: 54.64 kPA
Problem 4. Two strain gages are mounted on a thin-walled cylindrical pressure vessel. One strain gage is oriented parallel to the longitudinal axis of the thin-walled cylindrical pressure vessel while the other strain gage is perpendicular to the first. The tank has radius r= 20 in. and wall thickness of t= 0.4 in. It is made from a material that has %3D Young's Modulus E = 15x10® psi and Poisson's Ratio v =0.31. The strain gages in. report the following after the tank is pressurized: & = 133.0µ and ɛy = 591.5µ. in. in. in. E (& + v&µ) and ơ E From Hooke's Law: 0 (1-v*) (1-v²) Determine: Gage Pressure p
A square hollow bar having an outside dimension of 250 mm by 250 mm with 6 mm thick is to be replaced by a solid circular bar. a) Determine the required diameter of bar so that the maximum shear stress in the bar will not exceed the maximum shear stress in the tube. b) If the computed value of diameter in the previous question increase by 15%, what is the new shear stress of the circular bar? c) Determine the angle of twist in degrees of the tube if the length of the tube is 1m and the shear modulus is 80 GPa. Use T=14 kN-m.
The extruded plastic shape has dimensions of D = 39 mm, d = 33 mm, a = 87 mm, and t = 8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 350 N. (b) If the allowable shear stress for the plastic material is 1100 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a Answer: (a) Ta = kPa (b) V =
Please try to solve in 30 minute
A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowablestress is 250 MPa, Calculate the following:(a) Minimum required thickness of the plate. (Hint: HOLE vs FILLET) (b) Maximum allowable stress based on minimum thickness of the plate, Let K= 1.20 (c) Percent decrease on stress concentration
For a block with Young's Modulus of its material being 210 GPa and its Poisson's Ratio being 0.25, when subjected to a stress system as shown in the figure, what is the magnitude of the stress for no strain along AB? 60 N/mm A B 60 N/mm
The extruded plastic shape has dimensions of D = 23 mm, d = 21 mm, a = 93 mm, and t = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 360 N.(b) If the allowable shear stress for the plastic material is 2250 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :
A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowablestress is 250 MPa, Calculate the following: (a) Minimum required thickness of the plate. (Hint: HOLE vs FILLET) (b) Maximum allowable stress based on minimum thickness of the plate, Let K= 1.20 (c) Percent decrease on stress concentration