For the strain &¸ =&₂=0, Y=0.002828 (in x-y coordinate system) at a specific point in an isotropic material, using the Mohr's circle of strain to determine the strain components & , &₁, and ym in n-t coordinate system shown in the following figure. X 22.5° n

For the strain &¸ =&₂=0, Y=0.002828 (in x-y coordinate system) at a specific point in an isotropic material, using the Mohr's circle of strain to determine the strain components & , &₁, and ym in n-t coordinate system shown in the following figure. X 22.5° n

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: . For the plane stress situation shown in the figure, the maximum shear stress and the plane on…

A: A plane stress system as shown-Stress values-,To Find-The value of the maximum shear stress and the…

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A: Shear strain is measured as a change in angle between lines that were originally perpendicular.

Q: Learning Goal: To determine the in-plane principal stresses and maximum shear stress along with…

A: If you have any doubts please comment

Q: A point in a strained material is subjected to the stresses as shown in figure. The normal stress…

A: For a pointed strained material,to find The normal stress acting on plane inclined at 30o…

Q: The strain components & & and Yxy are given for a point in a body subjected to plane strain.…

Q: A thin polymer plate PQR is deformed such that corner Q is displaced downward 0.0525-in. to new…

A: Given data a = 9 in. , b = 1 in., c = 3 in., and Δ= 0.0525 in.

Q: A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The…

A: Shear strain is the ratio of displacement to an object's original dimensions due to stress, and is…

Q: At a point in a machine component that is subjected to plane stress, the normal and shear stresses…

Q: A piece of (A =53 mm × B= 29 mm) material experiences a homogenous deformation. The deformed shape…

Q: The plate is deformed into the dashed shape as shown. If in this deformed shape, the horizontal…

A: The plate is deformed into the dashed shape L = 340 mma = 7mmb = 4 mm It is asked to determine the…

Q: Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the…

A: Thin square plate PQRS;a = 200 mm,b = 202.1 mm,c = 198.9 mm.We have to determine-1. Shear strain xy…

Q: The following force-extension graph is for a cylindrical metal sample with cross section area of…

A: Given data:- The cross-sectional area,A=3.6 mm2 The length,L=240mm

Q: In order to determine the shear stress at A, using the shear stress formula, the thickness would be…

Q: The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain.…

Q: The state of stresses in the xand y directions at a point in a given material is shown in the figure…

A: step 1-

Concept explainers

Solid Mechanics

Engineering mechanics is a branch of science that deals with forces causing bulk motion in bodies and the effect that these forces cause on the bodies. Engineering mechanics does not deal with the internal changes that occur on account of these external forces. The internal effects in a body or a material under the action of external forces are studied in a new branch of science called solid mechanics, the strength of materials, or the mechanical behavior of engineering materials.

Question

100%

4. For the strain &¸ =ɛ, = 0, Y¸ = 0.002828 (in x-y coordinate system) at a specific
point in an isotropic material, using the Mohr's circle of strain to determine the
strain components &, &,, and ym in n-t coordinate system shown in the following
figure.
tn
y
22.5°
n

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Mohr circle ordinates for x and y plane

VIEW

Step 3: Mohr circle

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 100 MPa, σy=σy= 20 MPa, and τxy=τx⁢y= 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 68 GPa and v = 0.32 for the machine component.
A rectangular thin plate with Young's modulus 200 GPa and Poisson's ratio 0.30 is subjected to uniform stress distribution at its edges as shown. However it is stated that the dimension b of the plate does not change under the action of stress components , and om Considering microstrains (in 106), the change in the length of dimension a (in mm) is (rounded off to three decimal places) b- 100 mm O= 200 MPa Oyy = 200 mm
The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain. Determine the strain components & Et, and Ynt at the point if the n-taxes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle 8. Sketch the deformed shape of the element. Ex = -950 μE, Ey = 600 μE, Yxy = 1400 μrad, and 8 = 40° Answer: En = & بڑی = Ynt = με με Hrad n X
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1200 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3650 µrad. Assume a = 1.8 mm. Calculate the magnitude of dimension b in the figure. D Answer: b= i W B a mm X
20 and σ are the principal stresses at a point in a strained material. Poisson ratio for the material is 0.25. Modulus of elasticity of the material is 2.20. Total strain energy stored per unit volume of the material is ko. Then the value of k is (Round off to two decimal places.)
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
Figure Q4 shows a piece of triangular thin plate ABC with thickness 5 mm. A linear pressure as shown in the figure is being applied to edge AB with maximum intensity of 100 kN/m² at the middle of edge AB. The plate is made from stainless steel, with a Young's modulus of 200 GPa and Poisson's ratio of 0.3. The deformations in the plate are to be obtained. For such purposes, the finite element method is being employed. (a) (b) (c) (d) (e) State the type of problem involved in this case (to determine the stiffness matrix to be used). Model this problem optimally using the least number of orthogonal triangular elements only. Label the nodes and elements and indicate clearly the status of all the relevant degrees-of- freedom in this model. Set up the appropriate system of simultaneous equations and solve for the unknown displacements. Displacements at point T. Without any calculation, explain on the value of strain at points S and T.
The state of strain at the point has components of € = 300 (10-6), y = -260 (10-6), and Yay = 460 (10–6). Figure
At a point on the free surface of a machine component the strain rosette shown in the figure below
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1400 mm, and the height of the plate is h = 1900 mm. The shear strain at A is known to be +4294 μrad. Assume a = 2.4 mm. Calculate the magnitude of dimension b in the figure. D h Answer: b= i A W Ta mm 2