The evaporator (a heat exchanger) in an A/C unit has R-410A entering at -20 °C and a quality of 30% and leaves at the same temperature and a quality of 100%. The COP of the air conditioner is known to be 1.3 and the mass flow rate is given as 0.013 kg/s. Find the power input to the cycle. (Note that, here, the evaporator is the part of the A/C unit that accepts [i.e., withdraws] heat from the room maintained at a cold temperature)

The evaporator (a heat exchanger) in an A/C unit has R-410A entering at -20 °C and a quality of 30% and leaves at the same temperature and a quality of 100%. The COP of the air conditioner is known to be 1.3 and the mass flow rate is given as 0.013 kg/s. Find the power input to the cycle. (Note that, here, the evaporator is the part of the A/C unit that accepts [i.e., withdraws] heat from the room maintained at a cold temperature)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

* İl. Gmail ► Untitled docu.. A system consists of a turbine and heat exchanger are connected in series. The working fluid is entering the turbine at P1 0.6 Mpa, T= 200 °C and leaving it with P,= 0.2Mpa. Then the turbine exit becomes the heat exchanger inlet to increase the fluid temperature to become 800 °C. Considering that the adiabatic power y =1.4 and the specific heat = 1.005 KJ/Kg.K. Determine the turbine production work WT and heat exchanger energy needed to be added quE. T = 200 °C P,= 0.6 Mpa- T T2 ? P,=0.2 Mpa h high НЕ T= 800 °C P3 =? 9 in
I need the answer as soon as possible
A heat pump with refrigerant-134a (R-134a) as the working fluid is used to keep a space at 21 °C by absorbing heat from geothermal water that enters the evaporator at Ti,water = 60 °C at a rate of 0.067 kg/s and leaves at To,water = 40 °C. The specific heat of liquid water is 4.18 kJ/(kg∙K). Refrigerant enters the evaporator at TR-134a = 10 °C with a quality of x = 12 % and leaves at the same pressure as saturated R-134a vapor at the same temperature. The compressor consumes 1.4 kW of power. 1)Determine the mass flow rate (in kg/s) of the refrigerant. 2)Determine the rate of heat (in kW) supplied to the space. 2)Determine the COP of the heat pump. 4)Determine the ideal minimum power input (in kW) to the compressor for the same rate of heat supply
Given • isentoopie efficiency of the turbine isentropie · To find 86 and 91% If Dolynesi toraction Shoud not 86%. " of Pump = 91% Boiler = at State 6 be more than 1%. 1% Thermal efficiency of Puant 2 MPa (Pump 13 MPa, 600 C Turbine Condenser
ROOM (2) 700kPa x-0 CONDENSER k (1) 40°C 700OkPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? CA122.minutes O D112 menute COMP.
ercise 6 6.1 A surface condenser is fitted with separate air and condensate outlets. A portion of the cooling surface is screened from the incoming steam and the air is passes over these screened tubes to the air extraction and becomes cooled below the condensate temperature. The condenser receives 20 000kg/hr of dry saturated steam at 36.2°C. At the condensate outlet the temperature is 34.6°C TK and at the air extraction the temperature is 29°C. The volume of air and vapour leaving the condenser is 3.8m3/min. Assume constant pressure throughout the condenser, calculate: 6.1.1 the mass of air removed per 10 000kg of steam (2.63kg); 6.1.2 the mass of steam condensed in the air cooler per minute (0.5kg/min)%3B 6.1.3 the heat rejected to the cooling water (13451kW).
I need help on the following question: The vapour compression cycle (picture provided), utilises the refrigerant R134a flowing at 0.05 kg s-1. Assuming that the compression is adiabatic and reversible. If the actual input power to the compressor is 2 kW, then: 1. You need to determine the theoretical input power to the compressor and the heat transfer (Φ) to theevaporator. Take the enthalpies h1, h2, and h3 to be 238.41, 263.68 and 81.5 kJ kg-1 (use the 'NH3 Refrigeration Table' where you can find online). 2. You need to determine the coefficient of performance based on your answer to the previous question (1). 3. You need to determine the compressors mechanical efficiency.
Steam enters the turbine at 10 MN/m2and 450oC. The steam expanded in the turbine down to the condenser pressure of 20 kN/m2. The condensate leaving the condenser is pumped to the boiler pressure directly. The turbine has an isentropic efficiency of 89%, and the mass of steam generated in the boiler is 5 kg/s. Find: Cycle thermal efficiency. Plant power output.Neglect the pump work and draw the cycle on a T – s diagram. Hint: 1 MN/m2= 10 bar
Nitrogen at a flow rate of 0.1 kg / s enters a heat exchanger at a temperature of 450 K and 320 It comes out at K temperature. The other fluid of the heat exchanger is water, it enters at 20 ° C and leaves at 35 ° C. a) Calculate the flow of water. b) Calculate the entropy generation in this heat exchanger. (Take the average specific heating heat for nitrogen as 1.042 kJ / kgK.)