Answered: The diagram below shows all the… | bartleby

Related questions

Question

Please use the picture provided to answer the following two questions:

1. are the two sources in phase or out of phase? Explain how you can tell from the diagram. if the two sources are out of phase, give the phase difference between the two sources. Explain.

2. What is the source separation, d, in terms of the wavelength lamda? Explain your reasoning.

The diagram below shows all the antinodal lines (dashed) and nodal lines (solid) due to two point sources tapping a water surface
(the two dots in the middle of the circle are the two point sources). The sources are separated by an unknown distance d. The
sources lie along a horizontal line.

Expert Solution

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Blurred answer

Similar questions

Part A Green light shines through a 100-mm-diameter hole and is observed on a screen. If the hole diameter is increased by 20%, does the circular spot of light on the screen decrease in diameter, increase in diameter, or stay the same? Explain. Match the words in the left column to the appropriate blanks in the sentences on the right. Reset Help The wavelets do not and so the diameter of the spot of light on the screen with the hole's interfere in this case diameter. The diameter of the central maximum is inversely proportional to the diameter of the hole The diameter of the central maximum is proportional to the diameter of the hole The hole is too large to observe the diffraction increases decreases does not change
A light wave in vacuum has a frequency of 3.00 x 10¹4 Hz and an intensity of 810 W/m². s What is the wavelength of this light wave? Show your work. What is the magnetic field amplitude of this light wave? Show your work.
A. It appears that there should be a bright fringe at the location of point D. Why isn’tthere? Explain The previous figure is also labeled with points A and B which are at the locations of maximaand points C and D which are at the locations of minimum For Questions b and c below,you will need to discuss whether each of those minima/maxima stays at the same location,moves to the left or moves to the right and then explain your answers for each B. The slit width is slightly decreased C. The slit separation is slightly decreased.
PHET Simulation - Wave on a String Submit Previous Answers v Correct The effect of damping is akin to the absorbance or partial reflection of light, whore the amplitude of in phase photons becomes reduced. Part B Reset the PHET simulation (using the button in the lower tight) and set it up in the following manner select Oscillate, select No End, and use the parameters in parentheses by sliding the bars for Amplitude (1.00 cm). Frequency (2.00 Hz). Damping (none), and Tension (highest) Using the available Rulers, calculate the frequency of a photon that corresponds to the wavelength of the resulting wave. Assume the length with umits (cm) of the ruler represents the real photon wavelength and that the spced of light is 3.00 x 10° m/s. Express the frequency in hertz to two significant figures. > View Available Hint(s) ΑΣφ frequency= Hz Submit Part C Complete previous part(s) 452 PM P Type here to search Fi 322021
Green light shines through a 100-μm-diameter hole and is observed on a screen. If the hole diameter is increased by 20%, does the circular spot of light on the screen decrease in diameter, increase in diameter, or stay the same? Explain. Match the words in the left column to the appropriate blanks in the sentences on the right. The wavelets do not interfere in this case The diameter of the central maximum is inversely proportional to the diameter of the hole The diameter of the central maximum is proportional to the diameter of the hole Submit The hole is too large to observe the diffraction increases decreases does not change Request Answer diameter. and so the diameter of the spot of light on the screen Reset with the hole's Help
please check this answers
Part A You have been asked to measure the width of a slit in a piece of paper. You mount the paper 80.0 centimeters from a screen and illuminate it from behind with laser light of wavelength 633 nanometers (in air). You mark two of the intensity minima as shown in the figure, and measure the distance between them to be 17.9 millimeters. (Figure 1) What is the width a of the slit? Express your answer in micrometers, to three significant figures. • View Available Hint(s) ? um Subrnit Part B If the entire apparatus were submerged in water, would the width of the central peak change? > View Available Hintís) Figure O The width would increase. O The width would decrease. O The width would not change. Submit -17.9 mm- Provide Feedback
Part A The color of dyes results from the preferential absorption of certain wavelengths of light. Certain dye molecules consist of symmetric pairs of rings joined at the center by a chain of carbon atoms, as shown in (Figure 1). Electrons of the bonds along the chain of carbon atoms are shared among the atoms in the chain, but are repelled by the nitrogen-containing rings at the end of the chain. These electrons are thus free to move along the chain but not beyond its ends. They look very much like a particle in a one-dimensional box. For the molecule shown, the effective length of the "box" is 0.85 nm. Assuming that the electrons start in the lowest energy state, what is the longest wavelength this molecule will absorb? Express your answer with the appropriate units. На ? A₁ = Value Units Submit Request Answer ▾ Part B Assuming that the electrons start in the lowest energy state, what is the second longest wavelength this molecule will absorb? Express your answer with the appropriate…
Yellow light with wavelength 600 nm is travelling to the right (in the positive x direction) in vacuum. The light is polarized along the +y direction. The light passes an observer X located on the x axis. (a) Draw a neat labeled movie mode vector picture of the wave at the location of AX. (b) If the wave were to represent blue light instead of yellow light, how would your diagram in part a change? Draw a new diagram to explain these changes. If there is no change, say so explicitly.