The cylinder shown in Fig. 16-15a rolls without slipping on the surface of a conveyor belt which is moving at 2 ft/s. Determine the velocity of point A. The cylinder has a clockwise angular velocity = 15 rad/s at the instant shown. 0.5 ft TA/B B (b) 45° @= 15 rad/s (a) 45° TAB B vc =2 ft/s w = 15 rad/s VB = 2 ft/s w = 15 rad/s I 0.5 ft Relative motion (c)

The cylinder shown in Fig. 16-15a rolls without slipping on the surface of a conveyor belt which is moving at 2 ft/s. Determine the velocity of point A. The cylinder has a clockwise angular velocity = 15 rad/s at the instant shown. 0.5 ft TA/B B (b) 45° @= 15 rad/s (a) 45° TAB B vc =2 ft/s w = 15 rad/s VB = 2 ft/s w = 15 rad/s I 0.5 ft Relative motion (c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Answer the two problems indicated in the photo
Please and thank
For the following mechanism, rod AB is pinned to the two disks at point A and point B, and the two disks roll to the left without slipping. if the length of rod AB, I= 2.4 m, and its angular velocity @ = 6.2 rad/s, determine the magnitude of the linear velocity of point B. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. (0.5 m 0.5 m No slipping No slipping Your Answer: Answer units
3
4. At the instant shown, the crank AB is rotating with a constant counterclockwise angular velocity of w rpm. Determine the velocity and acceleration of point B in terms of normal and tangential components. W = 44 29.4 45° rpm l = 73.8 .mm l mm Figure 4.
The hoisting gear A has an initial angular velocity of 80 rad/s and a constant deceleration of 4 rad/s² (Figure 1) Figure 2 ft 4 05 f 1 of 1 Part A Determine the velocity of the block which is being hoisted by the hub on gear B when t = 2 s Express your answer to three significant figures and include the appropriate units. Uw = Submit Part B aw = HA Value Submit Request Answer 0 Determine the magnitude of the deceleration of the block which is being hoisted by the hub on gear B when t = 2 s. Express your answer to three significant figures and include the appropriate units. HA Value ft/s 1 Request Answer p Pass ft/s² ? BARCE ?
2. Two rigid links are rotating in the horizontal plane as shown in the figure below. The left-most link rotates with angular rate ₁ of 4 rad/s. The end of the right-most link holds a pin which is confined to move along a slot in the other link. The length of the right-most link 72 is 0.45 m. Determine the angular rate ₂ of the second link at the instant shown. Use 0₁ = 30°, 0₂ = 60°, and r₁ = 0.6 m. 0
If the gear is rotating at an angular speed of (2rad / s ) and the rack Z is moving with acceleration of (6 ft / s^2) to the Left, answer the following questions: Note: The wheel is always in contact, without slip, with the fixed path F. 1. The angular acceleration of a gear, gear a (,) a positive value means inverting Clockwise rotation and negative value means clockwise) 2. Acceleration of point 0 on gear (vector ao) 3. Acceleration of point A on gear (vector aq) 4. Acceleration of point E on the acceleration (wheel) (vector g @) 5. Point B acceleration in gear (vector g @)
= At the instant shown rod AB has an angular velocity WAB 4 rad/s and an angular acceleration AB 2 rad/s2. Determine the angular velocity and angular acceleration of rod CD at this instant. The collar at C is pin connected to CD and slides freely along AB. = a) using the relative motion analysis and the contact conditions. A 4 rad/s AB= 2 rad/s² WAB 60° 0 = 0.75 m -0.5 m В B D
A9
only Handwritten answer needed please. not typed
12. The gear A on the drive shaft of the outboard motor has a radius r = 0.5 in. and the meshed pinion gear B on the propeller shaft has a radius r = 1.2 in. . (a) Determine the angular velocity of the propeller in t = 1.5 s, if the drive shaft rotates with an angular acceleration ,a = (400t³) rad/s², where t is in seconds. The propeller is originally at rest and the motor frame does not move. (b) Determine the magnitude of the velocity and acceleration of point P located on the tip of the propeller at the instant. t = 0.75 s 2.20 in.