The wheel shown in the figure (not to scale) rolls to the right with a constant velocity of 1.25 m/s. The distance AD is 67.5 mm. Determine (i) the velocity of the collar at B and (ii) the angular velocity of the rod AB when... (a) B= 90° (b) B=0° 108 mm- D A 337.5 mm B 216 mm

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: solve and show each step in solution

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: Write force F2 in vector form

A:

Q: 1. A building exhaust fan for a large commercial bullding weighs 180 pounds and operates at a speed…

A: VIBRATION ISOLATORS A vibration isolator is a flexible component interfacing gear and establishment…

Q: 1.39 The bar AB is supported by a frictionless inclined surface at A and a 7/8- in.-diameter pin at…

A:

Q: Water at 10°C flows through the system shown in the figure below at 0.28 m³/s. Energy loss in the…

A: Temperature of the water vessel. T1=10°C Diameter of the pipe. d =30cm=0.3m Diameter of the pipe…

Q: Calculate the reaction force on the gate from the smooth support at A (FAz) in [N]

A:

Q: Determine the internal shear force at point C Express your answer to three significant figures and…

A:

Q: USE IMAGE BELOW! Solve for parts A through C and Label Them

A:

Q: Air enters a compressor operating at steady state at 105 kPa, 300 K, with a volumetric flow rate of…

A:

Q: 8-1. A cylinder 24 in. in diameter on shaft S drives, by pure rolling contact, another cylinder 2 on…

A: Given:Diameter of cylinder on shaft S, ds=24 inSpeed of shaft S, Ns=600 rpmSpeed of shaft T,…

Q: Two identical 4 in. major-diameter power screws (single-thread) with modified square threads are…

A: Given:f = 0.1fc = 0.24v = 3ft/min = 36 in /minTo find:Power required to drive each screw when the…

Q: 15) Consider a soccer player kicking a stationary ball of mass m = 0.5 kg. The angle of release of…

A: (a)

Q: Estimate the flow rate Q of water discharging from the nozzle as shown in Figure 3. If the fluid…

A:

Q: A local camera station is tracking a UFO sighting in the evening sky. Find the velocity and…

A:

Q: The pressure of water in a pipeline was measured by means of a simple manometer containing mercury.…

A: Consider the U-tube manometer according to the given queston as shown below, The manometer is…

Q: 7-39 Onekg of R-134a initially at 600 kPa and 25°C under- goes a process during which the entropy is…

A:

Q: A ductile material having an endurance limit of 196 N/mm2 and the yield point at 294 N/mm² is…

A: Given, Endurance limit = SE = 196 N/mm2 Yield limit = Sy = 294 N/mm2 Maximum stress = σmax = 147…

Q: Determine the specific volu ideal-gas equation of state

A:

Q: 1.50 An electric motor draws a current of 10 amperes (A) with a voltage of 110 V. The output shaft…

A:

Q: After performing an experiment in a manner similar to the procedure described in the lab manmal, it…

A:

Q: Q3: Two smooth balls A and B each have a mass of (350 g). If ball A strikes ball B with a velocity…

A:

Q: A motorist enters a motorway at a velocity of 8 m/s and accelerates uniformly. After traveling for…

A: Given data:

Q: The figure (not to scale) shows a representation of a hoisting system. A couple is applied to the…

A: Initial angular velocity of A, Final angular velocity of A, Time interval

Q: Draw the three standard orthographic views for the following object.

A: Draw the three standard orthographic views for the following object.

Q: 2.) If the applied force P = 600 N and the coefficient of kinetic friction between the 55 kg crate…

A:

Q: Problem A solid uniform ball with mass m and diameter d is supported against a vertical frictionless…

A:

Q: In the mechanism, as shown above, the crank OA rotates at 20 rev/min. anticlockwise and gives motion…

A:

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: A 3 lb motor is rigidly mounted in the middle of a 17.6 lb, 72 inch long beam, as shown in the…

A: Given:- Mass of the long beam=17.6lb Mass of the motor=3lb E=10 x 103 ksi I=0.625 in4 To find:- a)…

Q: GIVEN THE ORTHOGRAPHIC VIEWS, CREATE AN ISOMETRIC SKETCH OF THE FOLLOWING OBJECT.

A: According to the given data Three projection view of an object is drawn We need to draw Isometric…

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: I just need help drawing the KINEMATIC DIAGRAMand the GRAPHS (v-a, a-s, s-t, v-t, v-t, or a-t) if…

A: Given: The v-s diagram is shown below: From distance 0 to150 m, the equation of velocity line is…

Q: 2. A 50-g mass is suspended by a spring attached to the ceiling, such that when it is at rest, it is…

A:

Q: Defoomine max: ofeay sforess ?

A: Given: state of plane stress at point is:  σx=220 MPa  σy=100 MPa   ζxy=130 MPaFor the data given,…

Q: B 30° 3 m 2 m - 10 m

A:

Q: For a reactor, the following reaction rates are given by Fission rate (=[ dVE,6): 3.6×10* fissions /…

A: Part akeff=Neutron production from fission in one neutron generationNeutron absorption and leakage…

Q: For the system shown in the figure, and y denote the absolute displacements of the mass m and the…

A: Dear Students

Q: 4-3. The motion of the rigid body m is such that the point A moves in a circular path of 1-in.…

A: Given: To find: Velocity and acceleration polygon

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.