The cross-sectional diameter of aluminum nail measures 1.50 mm and it is projected outward to a length of 3.50 cm horizontally from a wall. A wet raincoat having a mass of 2.60 kg is hanged on one end of the nail. Assuming the wall holds the other end of the nail, what is the vertical deflection at end of the nail where the raincoat is hanged? The shear modulus of aluminum is 2.40×101º N/m?. 4.

The cross-sectional diameter of aluminum nail measures 1.50 mm and it is projected outward to a length of 3.50 cm horizontally from a wall. A wet raincoat having a mass of 2.60 kg is hanged on one end of the nail. Assuming the wall holds the other end of the nail, what is the vertical deflection at end of the nail where the raincoat is hanged? The shear modulus of aluminum is 2.40×101º N/m?. 4.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ How much fluid is required to raise the pressure in a thin cylinder of length 3 m, internal diameter 0.7 m, and wall thickness 12mm by 70kN/m*? E = 210GN/m* and v = 0.3 for the material of the cylinder and K = 2.1 GN/m* for the fluid.
Mechanics of deformable bodies
How do I approach this problem?
A cylindrical rod has initial dimensions of length ? = 4 m andradius ? = 1 cm. When the rod is pulled in tension axially withan external force of ? = 200 kN, the rod deforms to newdimensions of length ?′ = 4.024 m and radius ?′ = 0.998 cm.Determine the modulus of elasticity of the rod and its Poisson’sratio. Assume the rod deforms in the elastic range.
A normal-weight concrete masonry unit is 40cm by 20cm by 15cm thk. A wall made up of this material, fully grouted and plastered, is supported by a beam. The wall dimension is (H x L) 3m by 5m. The plaster thickness on both wall faces is 15mm. The density of the unit is 21.2 kN/m³, while the density of the grout is 22 kN/m³. Determine the conservative superimposed dead load on the beam in kN/m. Use two decimal places.
I Review If the cable can sustain a maximum tension of 1.5 kN and the maximum sag is 3 m, determine the maximum distance L between the supports. The 10 kg/m cable is suspended between the Express your answer using three significant figures and include the appropriate units. supports A and B (Figure 1) • View Available Hint(s) Figure < 1 of 1 μΑ ? L = 8.68 m L. Submit Previous Answers Request Answer 3 m B
What is the stretched length in DB? What is the tesion in spring DB? What is the unstretched length in DB?
Two builders carry a sheet of drywall up a ramp. Assume that W = 1.9 m, L = 3.3 m, theta = 19.0⁰, and that the lead builder carries a weight of 109.0 N (24.5 lb). L- Ө What is the weight carried by the builder at the rear? HINT: Consider the drywall to have no thickness. The builder at the rear gets tired and suggests that the drywall should be held by its narrow side. ~W~ 0 What is the weight he must now carry? HINT: From the previous problem, you know how much each builder carries. Therefore you know the total weight. Set the sum of the torques about the front lower corner to 0, so that you do not need to know the weight carried by the builder in front.
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.1 cm & the external diameter of 22.7 mm is subjected to an elastic tensile load of 271 kN. Take the elastic modulus of the aluminum specimen as 73 GPa and the initial length of the hollow cylinder as 186 mm. Solution: i) Cross-sectional Area (in mm2) = ii) Stress-induced (in N/mm2) = iii) Strain-induced (at least 3 decimal places accuracy)= iv) Elongation (in mm) =
2) On your birthday, your friends stack two presents, A and B, on a horizontal surface. A ribbon is tied to the upper right corner of block A. Assume the packages can only move horizontally and that u1-s = 0.4, µ1-k = 0.35, µ2-s = 0.2, zk = 0.15, mA = 10 kg and mg = 1 kg. Determine if package A will slip if you pull on the ribbon with a force T = 30 N. Be sure to include an FBD and IRD. > If package A slips, determine the acceleration of the package when you pull on the ribbon. > If package A does not slip, determine whether both packages slip on the floor when you pull on the ribbon (this would require a new FBD and IRD of the entire system). If they slide, compute the acceleration of the system. 1m e = 45° 0.3 m D.3m 1.2m
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
Determine the bulk modulus for each of the following materials: (a) rubber, Er = 0.4 ksi, nr = 0.48, and (b) glass, Eg = 8(103) ksi, ng = 0.24.