The cross-sectional area of each member of the truss is 690.69 in^2. Calculate the stresses in members BD, BE and CE. (answers in psi).
Q: Calculate the mass of a solid gold rectangular bar that has dimensions lwh = 4.00 cm ✕ 15.0 cm ✕…
A: Volume, V = 4 cm x 15 cm x 27 cm density, d = 19.3 x 1000 kg/m3
Q: The rigid bar BDE is supported by two links AB and AD. Link AB is made of aluminum (E = 70 Gpa) and…
A: First we calculate the force on B and D. For this we draw the Freebody diagram, On AB,
Q: A metal rod that is 12.0 m long and 0.74 cm2 in cross-sectional area is found to stretch 0.27 cm…
A:
Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…
A: Calculate the stress in steel section.
Q: a wire of radius 0.2 x 10^-3 m is suspended from the ceiling.When a weight (force) of 5.0N is…
A: Given, Weight (force) hanging,F=5 N Radius of wire, r=0.2×10-3m
Q: e plates in shear, what is the shear
A: We know, Shear stress=force/Area Given, Force=47kN Diameter=3.25mm Radius=1.625mm
Q: Problem 1.38 The horizontal link BC is t= 6 mm thick, has a width w 30 mm and is made of a steel…
A:
Q: Compute the fractional change in volume of a glass slab, when subjected to a hydraulic pressure of…
A: The bulk modulus is given by
Q: Using the method of joints, determine the magnitude of force (Ib) in member BC of the truss shown if…
A: In this question we have to use the method of joints and we have to determine the magnitude of force…
Q: Find the stresses in members BC, BD, and CF for the truss shown in Indicate the tension or…
A:
Q: A 5.25-m-long steel rod must not stretch more than 2.48 mm and the normal stress must not exceed 181…
A:
Q: A 9 16 -in.-diameter steel rod is tested in tension and elongates 0.00715 in. in a length of 8 in.…
A: Let the Diameter of rod (d) = 9.16 inch d = 0.23 metre length (l) = 8 inch l = 0.20 metre mass (m)…
Q: A hydraulic press contains 0.25m^3 of oil. It is subjected to a pressure increase of 1.6x10^7 Pa.…
A: Have a look at solution dear
Q: A tensile force of 2150 N is applied to a 12m steel beam with a cross-sectional area of 5.2 x 10-4…
A:
Q: 2.31. The three principal stresses at a given point are o=60 MPa, o2=-100 MPa, 03 =-10 MPa. If the…
A: Given: The principal stresses at a given point are 60 MPa, -100 MPa and -10 MPa. Introduction: The…
Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…
A: stress is defined as the force per unit area. Write the expression for stress. S=FA…
Q: A steel bar is 10 mm in diameter and 2 m long. It is stretched with a force of 20 kN. Calculate the…
A: Given data: Diameter (d) = 10 mm = 0.010 m Length = 2 m Force (F) = 20 kN = 20 × 103 N Required: The…
Q: An aluminum specimen 15 in long and in in diameter is subjected to tensile stress. The new length of…
A:
Q: Calculate the mass of a solid gold rectangular bar that has dimensions lwh = 4.40 cm ✕ 13.0 cm ✕…
A: Formula of density is as follows; ρ=mV…
Q: A force of 25ON is applied to a steel wire of length 1.5m and diameter 0.60 mm. Calculate the…
A: Given Force F = 250 N Length L = 1.5 m Diameter = 0.6 mm Radius r = 0.6/2 = 0.3 mm = 0.3 × 10-3 m
Q: Calculate the mass of a solid gold rectangular bar that has dimensions lwh = 4.25 cm ✕ 10.5 cm ✕…
A: Expression for the mass is m=ρV=ρlwh=19.3×103 kgm34.25×10-2 m×10.5×10-2 m×23.5×10-2 m=20.2 kg
Q: A short timber post of rectangular section has one side twice the other. It contracts by 0.05 cm/m.…
A:
Q: A short timber post of rectangular section has one side twice the other. It contracts by 0.05 cm/m.…
A:
Q: A brass rod with a length of 1.40 m and a cross-sectional area of 2.00cm2 is fastened end-to-end to…
A:
Q: Calculate the mass of a solid gold rectangular bar that has dimensions lwh = 5.30 cm ✕ 12.0 cm ✕…
A: Density is defined as the ratio of mass and volume . Mathematically, this is expressed as, ρ=MV V is…
Q: Suppose that a 6-mm diameter steel has a breaking stress of 5.5x108 Pa. What will be the diameter…
A:
Q: 3. Compute the modulus of elasticity of a copper alloy wire that stretches 14 mm when subjected to a…
A:
Q: One end of a wire 2 m long and 02 cm in cross-section is fixed in a ceiling and a load of 4:8 kg is…
A:
Q: te=120 (2) 457 tレ Oa = 60 the figure (0,c=0), find the principal Q-For the plane stress case shown…
A: Given : A plane stress case.
Q: what is the stress on a bar with n cross-sectional area of .05 sq in that is subject to a 100,000lb…
A:
Q: A lead cube has a total mass of 91 kg. What is the Length of its side in cm? specific gravity of…
A: We are given specific gravity of lead. We first find the density of lead. We are given mass of lead.…
Q: Steel beams are used for load bearing supports in a building. Each beam is 4.0 m long with a…
A:
Q: If the long term permissible load capacity for three nails in double shear in C22 timber is given as…
A: Force on the nail F=1660.5N Area =3.35mm x 90mm
Q: The two pieces of wood, 2.39in. by 6.01 in., are glued together along the 54°joint. Determine the…
A: Concept: To determine the Normal Stress we will have to calculate the maximum safe axial load (P)…
Q: Calculate the mass of a solid gold rectangular bar that has dimensions lwh = 5.30 cm ✕ 13.0 cm ✕…
A: Given data The dimension of solid gold rectangular bar is: lWh = 5.30 cm X 13.0 cm X 23.0 cm The…
Q: A wire of circular cross-section, has a tensile force of 60.0 N applied to it and this force…
A: Here, σ=FAA=Fσ=60.0N3.06×106 Pa=19.61×10-6 m2=19.61 mm2
Q: What shear stress is needed to produce a shear strain of 2.50 x 105 on an aluminum block?
A: Given data: Shear strain of Aluminum block is, εs=2.50×10-5.
Q: One end of a steel rod is connected to one end of a copper rod. The copper end of the composite rod…
A:
Q: A cast iron rod of diameter 18 mm and length of 240 mm is subjected to a tensile load of 100 kN, and…
A: Given. T = 100KN = 100,000 N D = 18mm = 0.018 m L = 240mm = 0.24m ∆L = 0.0006 m
Q: An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 216…
A: Answer: Normal stress, σ =2.73×108 N/m2 Shear stress, τ =1.51×108 N/m2
Q: A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is…
A: i. The cross-sectional area of the rope is given by,
Q: The force F (in newtons) of a hydraulic cylinder in a press is proportional to the square of sec x…
A: When the force is directly proporitonal to the square of secx, the function can be written as:…
Q: The stress experienced by a certain surface is 17612Pa when a 17-N force is applied to it. How much…
A:
Q: A steel beam is placed vertically in the basement of a building to keep the floor above from…
A:
The cross-sectional area of each member of the truss is 690.69 in^2. Calculate the stresses in members BD, BE and CE. (answers in psi).
![.'
8' E
8'
B
8'
6'
30 kips
C](/v2/_next/image?url=https%3A%2F%2Fcontent.bartleby.com%2Fqna-images%2Fquestion%2F8e1efa49-6357-4d52-8419-0b8942338039%2F784c89e9-feaa-45e2-b759-c63aadb4b2ad%2F4101nyh_processed.jpeg&w=3840&q=75)
![](/static/compass_v2/shared-icons/check-mark.png)
Step by step
Solved in 5 steps with 3 images
![Blurred answer](/static/compass_v2/solution-images/blurred-answer.jpg)