Problem 1.38 The horizontal link BC is t= 6 mm thick, has a width w 30 mm and is made of a steel with a 450 MPa ultimate strength in tension. Determine: The factor of safety if the structure shown is designed to support a load P 40 KN? 150wm 00 vum
Q: In (Figure 1), σy Figure = 49.1 MPa. Determine the principal stresses. Specify the orientation of…
A: Step 1: Step 2: Step 3: solution is given above Step 4:
Q: A brass rod 5ft long with a square cross section 0.5 inch on a side is used to support a 520-lb load…
A: B=F/AL'/L=FLL'AL'=FLBA F is the load L is the original length B is the bulk modulus A is the cross…
Q: E. A steel rope is subjected to a tension F N(480, 94)KN, and its bearing capacity is Q~N(740,…
A: In this we have to calculate the torsional stress in a shaft which is written as product of…
Q: 206. A steel wire 30 ft long, hanging vertically, supports a load of 500 lb. Negiecting the weight…
A: The stress (S) on a wire is the load (F) on it divided by its cross-sectional area (A). Use this…
Q: For the figure shown, if the stress in steel is 75 MPa, then ....... the stress in the copper is
A: Write the expression for strain developed. σESteel=σECopper
Q: 6. A steel rectangular block 1.5 in. wide, 3/4 in. deep and 5 in. long is subjected to an axial…
A:
Q: A 5.25-m-long steel rod must not stretch more than 2.48 mm and the normal stress must not exceed 181…
A:
Q: RJA hollow cylinder is to be punched out of a sheet of aluminum. The inner radius is 1cm and outer…
A:
Q: f a compressional stress of 200.0 N is applied to a copper rod having a diameter of .500 cm and a…
A:
Q: Please help me with this solution.
A: In the given, we can find the ultimate shearing stress of the shear pin by:First, we calculate the…
Q: 1. In the system shown, cable A has an Ultimate Stress of 201 MN/m². For this application the cable…
A:
Q: nd trim printed circuit sheets. For the position shown, determine the vertical component of the…
A: Px = 390 sin 13 = 87.73 NPy =390 cos 13 = 380 N(FBD)x =2510034 FBD(FBD)y =9710034FBD
Q: A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200…
A: Solution:-Given thatsquare steel barside (a)=50 mmlength (L)=250 mmAxial tensile force (F)=200…
Q: The cross-sectional area of the bar is 5 cm?. Use E= 70 GPa for aluminum, and E= 200 GPa for steel.…
A:
Q: a)What is the magnitude of the bone shear force acting on the vertebra?Report in N b)what is the…
A: The objective of the question is to calculate the magnitude of the bone shear force and the bone…
Q: Determine the maximum safe load P if a factor of safety of 3.75 with respect to failure by yield is…
A:
Q: In Buckling test: find Fc for the steel rod with dimensions (b-4.0 mm, h-2.0mm), its E =200 Mpa, and…
A: Given that, the rod is fixed E=200 MPa=200 N/mm2L=25 cm=750 mmb=4.0 mmh=2.0 mm The formula to…
Q: The shear stress in power-law liquids in steady state laminar flow is given by the equation du, T,-…
A: We have given that- τrx=-∆Pfs2Lrwe have,τrx=K-duxdrnPut the value of τrx…
Q: 1.18 A load P is applied to a steel rod supported as shown by an alu- minum plate into which a…
A: l=12 mm sheering stress=180mPa The Stress of an aluminum plate: 70mPA
Q: A rectangular steel block is 4 inches long in the x direction, 3 inches long in the y direction, and…
A: Given: Lx=4 inch Ly=3 inch Lz=4 inch Fx=48 kips Fy=-60 kips Fz=54 kips
Q: Suppose that a 6-mm diameter steel has a breaking stress of 5.5x108 Pa. What will be the diameter…
A:
Q: 3. Compute the modulus of elasticity of a copper alloy wire that stretches 14 mm when subjected to a…
A:
Q: Artificial diamonds can be made by putting carbon in high-pressure high-temperature presses. Suppose…
A: Given:pressure = 6 GPa.Bulk modulus = 194 GPaVolume,v=1ccwhen you realease the pressure bring it…
Q: The cross-sectional area of each member of the truss is 690.69 in^2. Calculate the stresses in…
A: Given : A=690.69 in2In this question we follow steps to…
Q: Find the Viscosity Index of a fluid that has a viscosity of 32 cSt at 40 degrees C. The O VI and 100…
A: The viscosity index VI is an arbitrary, unitless measurement of a fluid's viscosity variation as a…
Q: Please solve the question,I need Correct answer.
A: Given Data:Power (P): P=15hpRotational speed (N): N=1000rpmDiameter of the Shaft (d):…
Q: The A-36 steel wire AB has a cross-sectional area of 11 mm² and is unstretched when 0 = 45.0°…
A:
Q: A tensile load of 45 kN is applied to 15 mm diameter bar. Calculate the engineering stress on the…
A: Data Given , Tensile load ( P ) = 45 KN = 45×103 N Bar diameter ( d ) = 15 mm = 15 × 10-3 m…
Q: The two pieces of wood, 2.39in. by 6.01 in., are glued together along the 54°joint. Determine the…
A: Concept: To determine the Normal Stress we will have to calculate the maximum safe axial load (P)…
Q: The velocity v (m/s) of air flowing past a flat surface is measured at several distances y (m)…
A: Newton’s viscosity law,
Q: H horizontal force of P = 1,400 lb is applied to the rectangular bar shown in Figure above. d = 1.80…
A:
Q: Problem 1. 60° D 45° B 200 mm A It has a cross-sectional area of A-60mm and Young's modulus…
A: According to our guidelines We’ll answer the first part of the question since the exact one wasn’t…
Q: d A 12-mm-diameter steel [E = 200 GPa] rod (2) is connected to a 30-mm-wide by 8-mm-thick…
A:
Q: Problem 1: Load P = 24 kips compressing the concrete cylinder which length is reduced from 12 inches…
A: Load=24 Kips=106.75kN=106.75×103 N (1 Kips=4.448 kN) Original Length, L0=12 in=1 ft.=0.3048 m…
Q: A load of 300 N acts on a bar having a cross- sectional area of 0.6 mm2. The stress developed in the…
A: we know that,stress = force/area
Q: 3. Calculate the longitudinal and circumferential stresses of a steam boiler drum 2.15 m in diameter…
A:
Trending now
This is a popular solution!
Step by step
Solved in 2 steps with 2 images