The cross section of the cantilever retaining wall shown below. Calculate the factor of safety with respect to overturning, sliding, and bearing capacity. Ye = 24 kN/m 0.5m 10° Yi = 18 kN/m³ 1 = 30° C= 0.0 6m 1.5m 0.7m 07m-10.7m- 2.6m Y2 = 19 kN/m $2 = 24° C2 = 40KN/m2

The cross section of the cantilever retaining wall shown below. Calculate the factor of safety with respect to overturning, sliding, and bearing capacity. Ye = 24 kN/m 0.5m 10° Yi = 18 kN/m³ 1 = 30° C= 0.0 6m 1.5m 0.7m 07m-10.7m- 2.6m Y2 = 19 kN/m $2 = 24° C2 = 40KN/m2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Considering the effects of the construction process, calculate the displacements verticals for the…

Q: Check the design of the retaining wall shown below for sliding, overturning, and liftoff. Draw the…

Q: 4.5 m A Sand y = 16 kN/m 4'= 38° c' = 0 2.5 m B 3 m 1.5 m Figure P10.1

Q: Figure 5 shows a gravity retaining wall retaining a granular (c'=0) backfill. The same soil is…

Q: A retaining wall is supporting a backfill having a Ao = 23 kPa, y1 = 16.6 kN/m2 y2 = 19.0 kN/m? %3D…

Q: A reinforced earth retaining wall will have a height of 10.5 m. (35 ft) In this case: Calculate:…

A: Solution Given data height of 10.5 m. (35 ft)

Q: 0.30 WALL 3m or S/S D.P.C STEP-I 0.60 0.40 0.20 STEP-I o.Bo P.C.C 0 80 0.50

A: In this question superimposed load is not given so we will calculate the load of the wall for…

Q: The cross section of a cantilever retaining wall is shown in the figure below. Calculate QT the…

A: Shear stress and normal stress are ones know in the system but there are other quantities that can…

Q: A wall foundation( 1.3) m wide located at a depth of 0.8 m on a saturated soil…

A: Given : Width of foundation= 1.3 m Depth of foundation = 0.8 m ϕ=26° c=38 kN/m2 γsat=19.90 kN/m3…

Q: Calculate the stresses in members AB, DF, and BD. Given: FAB = 51.22 kN (C) FDF = 50 kN (C) FBD =…

Q: Situation: A T-beam is reinforced with 8-32mm diameter tension bars with an effective depth of…

A: Solution: Given: d = 700 mm b = 350 mm h = 800 mm t = 100 mm flange width = 750 mm fc = 27.60 MPa fy…

Q: a) Find the allowable load on the foundation by Terzaghi method, assuming a general shear failu with…

A: Answer Net allowable load = Qall Cohesion C =13 kpa Dry Unit weight of soil (γd) =17 Kn/m3…

Q: *The factor of safety against overturning The factor of safety against sliding *Calculate the…

Q: The cross section of a cantilever retaining wall is shown in Figure 1. Calculate the factors of…

A: In Dam there is Two types of force is acting on a dam, one is sliding force which cause overturning…

Q: A 2.2 m wide x 0.47 m thick RC footing is to be provided for a 250mm thick RC wall. The wall carries…

A: Answer Let us first draw the diagram of RC wall footing based on the given data Calculation of…

Q: Design the cantilever wall. Check that it complies with capacities for turning, sliding. And support…

A: i am answering to this problem according to bartleby guidelines step-1 include Given data things…

Q: A reinforced concrete retaining wall is proportioned as shown below. There is a water table located…

A: Solution Data given: Bulk unit weight, γ = 16.93 Submerged unit weight, γsat = 9.67 Angle of…

Q: Calculate the second column of the lateral stiffness matrix (Ri2, 02 = 1) for the confined masonry…

A: Let's work through the problem of calculating the second column of the lateral stiffness matrix…

Q: A slab shown supports the load W1 and W2 for every one-meter strip along the longitudinal section.…

A: Given: The value of L is 15 m. The value of w is 145 kN/m. Consider the figure,

Q: Q7: For the retaining wall shown in Figure below. Fined: 1- The value of (B) to makes FS)sliding FS)…

Q: By using Rankin theory, show if the wall shown in figure was stable against overturning, when the…

Q: = 16 kN/m², c; = 21 kN/m² = 17 kN/m³ cz= 22 kN/m? 18 kN/m³ cs = 23 kN/m?

A: a γϕ =γl1+ω =20.631+14 =18.0965 kn/m3b γϕ =1-naGγW1+WG =1-na2.67×9.811+0.14×2.67 =18.0965⇒0.0508…

Q: 0.00 m -10.00 m -18.00 m Ysat 17.0 kN/m³ = Ysat 18.0 kN/m³ = 6.00 m Cu-50 kPa, c'=5 kPa and '= 25°…

Q: Problem 17.28 The strongback is made of an A992 steel hollow circular section with the outer…

A: Given data : Steel = A992 Outer diameter = 61 mm P = 75 kN FS = 2 To Find : Determine the max,…

Q: Q8: For the retaining wall shown in Figure below. If FS)overturning = 9, find the value of () of…

Q: Question 1: The cross-section of a cantilever retaining wall is shown below. Calculate the factor of…

A: Consider the free body diagram;

Q: 5m W =? 6m

Q: Design the vertical stem of a T-shaped retaining wall for a height of 3 m above the ground level.…

Q: b. Lateral pressure due to soil (in kN/m2 per meter length of wall): @ point R = @ just above point…

Q: (127) 12.7 Refer to Figure 12.10. Given: H = 7 m, y = 18 kN/m³, d' = 25°, c' = 12 kN/m², unit length…

A: Given: H = 7m γ=18 kN/m3 ϕ=25o C = 12 kN/m2 α = 10o

Q: A one way continuous slab is to support a max. positive moment of 82 kN- m and a max. negative…

A: Given Data: Maximum positive moment is M1=82 kNm. Maximum negative moment is M2=245 kNm Maximum…

Q: If FA = 40 kN and FB = 35 kN, determine the magnitude of the resultant force and specify the…

A: Given:- FA=40kN FB=35kN To find:- x,y,FR

Q: The cross section of a cantilever retaining wall is shown in Figure 13.12. Calculate the factors of…

A: Soil boundaries give an idea of its compatibility with soil and water or both compounds. When the…

Q: A 8 m x 5 m rectangular slab is fixed at all edges and the support moment capacities are the same as…

Q: Using Rankine's earth pressures and neglecting the passive resistance, determine the factor of…

A: Step 1:Step 2:

Q: Figure below shows an excavation in sand, supported by braced sheet pile walls. The unit weight of…

Q: Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in…

Q: A wall footing has a width of 1.8 m supporting a wall having a width of 0.16m. The thickness of the…

A: Answer The footings are designed as shallow beams for the Moments and shear involved. For wall…

Q: Calculate the ratio of the actual soil pressure to net effective pressure. (q/qeff ).

A: The values given in the question are as follows Width of footing(B)=2.8 m The thickness of…

Q: Determine the stability of the wall in different conditions mentioned down in table and provide a…

Question

The cross section of the cantilever retaining wall shown below. Calculate the
factor of safety with respect to overturning, sliding, and bearing capacity.
Ye = 24 kN/m
0.5m
10°
Yi = 18 kN/m³
1 = 30°
C= 0.0
6m
1.5m
0.7m
07m-10.7m-
2.6m
Y2 = 19 kN/m
$2 = 24°
C2 = 40KN/m2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the cantilever retaining wall shown below. Calculate the factor of safety with respect to overturning, sliding, and bearing capacity. Wall dimensions: H=5.49 m, D=1.22 m, α=0°, X₁=0.46m, x2=0.58m, x3=0.92m, X4=1.55m, x5-0.61m. Soil properties: Y₁ 18.08 kN/m³, 1'=36°, Y2=19.65 kN/m³, 2²=15°, C₂ = 44 kN/m² X₁ H 72 $2
1. A one way continuous slab is to support a max. positive moment of 82 kN- m and a max. negative moment of 245 kN – m. Assume f'ċ= 20.7 MPa, fç = 138.23 MPa and n =9.2 1. Determine the minimum depth of the slab 2. Determine the steel area required at midspan. 3. Determine the steel area required at the support.
Check for overturning and sliding
Check the stability of the retaining wall shown in Figure against overturning and sliding. 5.5 m 25 kPa Y= 18 kN/m² 6=30⁰ c=0 3m Im Yoncrete 24 kN/m² 6-0,q.-210 kPa
Refer to the braced cut shown in the figure for which y= 20 kN/m², o'=23°, and c' = 0. 2.0000 The struts are located 5 m on center in the plan. Determine the strut load at B. 3.0000 B. 3.0000 2.0000 A 47.46 B 474.6 C 94.92 D 237.3
22.0
A reinforced concrete retaining wall is proportioned as shown below. There is a water table located H1m beneath the ground surface. Use ultimate bearing capacity of 450 kPa. Based on the figure, the dimensions are given below. Use γc = 23.48 kN/m3 wall thickness = 0.47m footing thickness = 0.53m toe slab length = 2.33m heel slab length = 4.38m ground water table depth = 2.99 H2 = 3.84 The following values were calculated for this particular retaining wall: Righting moment: 3,868 kN-m/m Overturning moment: 908 kN-m/m Total vertical load: 999 kN/m What is the factor of safety for bearing pressure? Please answer this asap for upvote. Thanks in advance
A 1.6 m wide x 0.46 m thick RC footing is to be provided for a 250mm thick RC wall. The wall carries a dead load of 160 kN/m and a live load of 225 kN/m of the wall. The gross allowable soil pressure is 323 kPa. The bottom of the footing is 670 mm below the ground. Use f'= 21 MPa and f, = 420 MPa. Unit weight is 23.6 kN/m3 for concrete and 18.4 kN/m3 for the soil backfill. Diameter of main bars is 16mm and that of the shirnkage and temperature bars 10mm Calculate the ratio of the Demand Shear Force to Shear Capacity in one- way shear. Answer in four decimal places. (i.e. 1.6125, 1.5140, 0.8461, etc.)
please help
A wall footing has a width of 1.4 m supporting a wall having a width of 0.24m. The thickness of the footing is 0.44m, and the bottom of the footing is 1.7m below the ground surface. If the gross allowable bearing pressure is 154 kPa, determine the actual critical shear acting on the footing, in KN. P(dead load) 294 KN/m = P(live load) 172 KN/m = yconcrete 24 KN/m3 = ysoil 19 KN/m3 = Depth of top of footing to NGL = 0.9 m concrete cover = 75mm assume db= 16mm dia.
For the retaining wall shown in the first picture, compute the factors of safety against overturning and sliding (analyze the latter both with and without passive earth pressure at the toe). Also determine the soil pressure at the base of the wall. Use the Rankine equation to compute passive earth pressure.