e. Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete. B = Thankyou please Y=15 kN/m4'=28°4mGW.T.Yu 20 kN/m4'-33°4mThe above figure shows a concrete gravity retainingwall supporting two layers of soil.Answer the following questions (a, b, c, d, e, f, g &h).Note:1. Use Rankine's theory of active pressure.2. Complete solution with diagrams is required forPS2.3. In all the steps in your solution, round the answersto three decimal places. This is important so youranswer will match the answer key.

Answered: Image /qna-images/answer/ba4918f9-85c2-4f19-aff5-35959a8c6372.jpg

Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete

Location of the total earth thrust from the base of wall (in meter) ya = f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at the base of wall is 25o and factor of safety against sliding is 1.5 (minimum). Consider 24 kN/m3 as the unit weight of concrete

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume a 27-in.-thick square footing (d 23 in) supports an 18-in.-square tied interior column. Assuming that the shear force V = 827 kips and the concrete used is 3000-psi normal-weight concrete, what exactly is the required depth to resist the two- way shear? Select one: a. 30.7 in b. 16.2 in А C. 36.8 in d. 23.9 in
For a simply supported prestressed concrete bearn, compute the stress in the top fiber at midspan due to prestressing force and service loads after transfer. Loss of prestressing force = 20%. Properties of the beam are: Width of the bearn, b: 242 mm; Depth of the %3D beam, d: 417 mm; Concrete cover of the bearn, cc: 61 mm; Prestressing Force, P: 574 KN; Superimposed Load, w: 14 KN/m; Length of the beam, L: 9 m. Stress is in unit MPa. Write only the value of your final answer. w (including selfweight) W „P.
Calculate the weight of the wall from the given Cross Section by considering the unit weight ofreinforced and plain concrete as γc=2Y kN/m3.
The reinforced concrete beam shown has a width of 400 mm and a total depth of 610 mm. It is loaded with a super imposed dead of 25 kN/m, and live load of 12 kN/m. Pdl =60kN and Pll = 40kN There are 3-25mm diameter bars arranged in a single layer at the bottom of the beam, with a clear covering of 50 mm. Another 2 -20 mm diameter bars are located at the top of the beam with the same clear covering. Determine the critical spacing of 10mm diameter stirrups. Use f = 28MPa, fy = 420 MPa, fyt = 275 MPa. P in KN P in KN w in kN/m Steel I Generic 7.0 m 2.0 m 5.0 m
Question 01. For the concrete gravity wall shown below: a. Determine the magnitude, direction, and sense of the resultant force./ b. Determine where the resultant intersects the base of the wall with respect to point A (horizontally)./ 2 m 70 kN 1 m 6 m 53 kN 21.0 kN 2 m 1 m 4.5 m
1.50 The cylindrical steel column has an outer diameter of 4 in. and inner diame- ter of 3.5 in. The column is separated from the concrete foundation by a square bearing plate. The working compressive stress is 26 000 psi for the column, and the working bearing stress is 1200 psi for concrete. Find the largest force P that can be applied to the column. Į 3.5 in 0.125 in. 0.75 in. 2800 lb 7 in. FIG. P1.50 1.5 in. 6 in.- 14800 lb B FIG. P1.49 6 in.-
eiches : Two-way slab system (6.1*6.1 m) as shown in Fig. 1, subjected to a live load of 2 kN/m² and superimposed dead load of 3.5 kN/m². Design the panel $2 for max positive and negative moments. The column dimension 300* 300 mm and the supporting beams are 300 mm width. Use fe=21 MPa and fy = 420 MPa arks). Fig.1 S2 6.1m 6.1m
A rectangular concrete beam has a width of 250 mm and a total depth of 450 mm. It is reinforced with a 4-20 mm Ø reinforcement bars placed at an effective depth of 375 mm. f'c = 27.6 MPa, Fy = 414.7 MPa. Determine the depth of compression block.
The floor shown below with an overall depth of 125 mm is to be designed to carry an imposed load (LL) of 2.5 kN/m² plus floor finishes and ceiling loads (DL) of 1.5 kN/m². Calculate the factored loads acting on beams CD. Assume unit weight of concrete is 24 kN/m². E 2. F 3.0 m 5.0 m Depth 125mn 0.125m -hh=2.5 kN/m² - PL = 1.5 kNm² - u. W of compete 24 KN/m³ A 80m B
Question
Give me right solution
A roadway sign weighs 7.4 kN and is supported by a structural pipe that has an outside diameter of 160 mm and a wall thickness of 11.5 mm. The resultant force of the wind pressure acting on the sign is 13 kN, as shown. Assume a = 8.7 m, b = 4.1 m, P₂ = 13 kN, and Py = 7.4 kN. (a) Determine the normal and shear stresses OH, Txy at point H. (b) Determine the normal and shear stresses OK, Tyzk at point K. Answers: OH = TxyH = OK = Tyzk = y HK i i i P₂ i b a MPa. MPa. MPa. MPa.