The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.

The cross section of a reinforced concrete beam is shown below. It has a modular ratio of 15. If the allowable compressive stress in the concrete is 6 MPa and the allowable tensile stress in the steel is 120 MPa, determine diameter of the three reinforcing steel rods to make the beam an economic section.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The cross section of a concrete dam is shown in the figure. Take the weight-density (= pg) of water to be 10 kN/m³ and that of concrete to be 25 kN/m³. For the given design of the cross-section, find the ratio h/H that is safe enough for the dam to not tip over (about the downstream edge E). Here you will enter the numerical answer. In the handworked file you must show your worked solution. H E 60° H/10 4H/10 h
solve the question given in the image.
For the beam shown at right, determine the following: P= 1800 lb a. Maximum tensile bending stress b. Transverse shear stress at a the junction of the "TEE" (i.e., 2" above the neutral axis). c. Transverse shear stress at the neutral axis - 7.5 ft- - 7.5 ft- (a) d. Draw the stress elements -10 in. representing the state of stress at the junction of the “TEE" and at the neutral axis. | 2 in. 4 in. -N- 1600 10 in. 8 in. 42 in.k- (b)
For the beam shown, use only singularity functions. V₁ = 45 lbf/in and V/₂ = 5 in. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 0 1400 lbf Hinge JA B₁ C R₂ R₁ 4 in 4 in 2 in V1 V2 D R₂ + What is the value of the peak moment between points Cand D? The peak moment between points C and Dis Ibf.in.
The cantilever beam is subjected to a concentrated load of P-32 kips. The cross-sectional dimensions of the rectangular tube shape are b-8.2 in, d - 13.30 in, and t-0.300 in. Determine: (a) the magnitude of the shear stress at point K, which is located to the left of the vertical centroidal axis at zx = 1.7 in. (b) the magnitude of the maximum horizontal shear stress in the rectangular tube shape. Answer: (a) Ti (b) Tmax= x ksi ksi (typ.) TK b エーミー H d
The beam shown below has a cross section of channel shape with width =200 mm and height h=80 mm, the web thickness is t=12 mm. Determine the maximum tensile and compressive stresses in the beam due to uniform load. And draw. 200 mm 3.2KN/ 2 KN.M 80mm 12mm 3m 15m
Since the safety normal stress of the wood used for the beam and loading condition shown in the figure is 12 MPa, determine the optimum cross section height (mm) of the beam.
A simply supported beam with a length of 4m is loaded with a uniform distributed load (w). The beam has a rectangular hollow section with the following dimensions: Outer Base = 150 mm OuterDepth 200 mm Inner Base = 100 mm Depth = 150 mm Inner Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the bending stress is limited to 8 Mpa. Please answer with solution and fbd. Thank you.
Find the Magnitude of the Maximum Shear Stress in the below beam and cross-section, if: W = = 6 kN/m L = 5 m b = 55 mm h = 144 mm Ensure that your answers are in MPa. Mo W Cross-Section: L b h
The figure shows the cross-section of a beam that is composed of a wide-flanged structural profile, whose specification is indicated in the figure, and two steel plates, joined by means of screws, placed in pairs with a longitudinal separation of 20 cm . If the beam is subjected to a vertical shear force of 25 KN, determine the shear stress supported by each bolt in the topsheet. Please add the free diagram body.
A 200 mm square hollow section at 15 mm thick, is used as simply supported beam both ends. The simple beam carries 10 kN/m uniformly distributed load applied on its entire span. Determine the maximum flexural stress (kPa) caused by the uniform load.
Two vertical forces of P = 240 lb are applied to a simply supported beam shown below having the given cross section shown below. Using a = 30 in., L = 84 in., b = 3.0 in., d = 4.0 in., and t = 0.5 in., calculate the bending stresses produced in the top and bottom of the beam.