5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E = 200 GPa and BD from aluminum with E = 70 GPa. The diameters of posts AC and BD are 25 mm and 40 mm, respectively. Determine the vertical displacement of point F on AB. 100 kN 200 mm 400 mm B F 300 mm

5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E = 200 GPa and BD from aluminum with E = 70 GPa. The diameters of posts AC and BD are 25 mm and 40 mm, respectively. Determine the vertical displacement of point F on AB. 100 kN 200 mm 400 mm B F 300 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E = 200 GPa and BD from aluminum with E = 70 GPa. The diameters of posts AC and BD are 25 mm and 40 mm, respectively. Determine the vertical displacement of point F on AB. 100 kN 200 mm 400 mm- B F 300 mm C D
2) A rigid beam AB rests on the two short posts as shown. Post AC is made from steel and has a diameter of 20 mm. Post BD is made from aluminum and has a diameter of 40 mm. Assume E = 200 GPa for steel and E = 70 GPa for aluminum. Determine the displacement (mm) of point F for a vertical load of 90 kN. A 90 kN 200 mm F -400 mm B D 300 mm
5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E-200 GPa and BD from aluminum with E-70 GPa. The diameters of posts AC and 80 are 25 mm and 40 mm, respectively. Determine the vertical displacement of point on AB 100 KN 400mm D 6. The timber beam has a cross-sectional area of 2000 mm and its modulus of elasticity is 12 GP Axial loads are applied at points B, C, and D as shown. Calculate the total change in length of the beam. Answer: 2.33 mm 40 KN 35 KN 20 KN 3.20 m 1.60m 3.20 m
If the beam shown is supported by the fixed wall at B and the rod AC. if the rod has a cross sectional area = 10 x10-4 m2 and is made of the same material of the beam if the area moment of inertia of the beam's cross section is 9.7 x 10-° m4 if the distributed load w = 8.5 kN, then, the tension in the rod AC is . ... N 1 m 1 m 2 m Oa. 27.57 Ob.926.32 Oc 6.38 Od. 63518.95
If Mz = 200 kip-ft, find the magnitude of the bending stress at a point H. For the beam cross section, assume a = 7 in. b = 10 in. d = 26 in. r = 3.5 in. The centroid of the cross section is located 11.96 in. below the uppermost surface of the beam. The moment of inertia about the z axis is 12903 in.4.
The rigid beam shown in is held by two vertical rods at A and C.If a 60 KN load is applied at B what is the displacement of this point (B) . Aluminum L- 3m A- 500 mm E- 70 GPa Steel L- 4 m A= 300 mm E- 200 GPa 3.5 m 2.5 m
If the following structural beam has a rectangular cross-section and is subjected to the loadings as shown below, determine the followings: c- c- The moment of inertia of the rectangular cross-section. d- d- The maximum bending moment in the beam. e- The absolute maximum bending stress in the beam. i wont c d e
Pravinbhai
A moment about the z-axis of 192 N-m is applied to a beam with dimensions b = 85 mm and h = 302 mm. If there are no other loads applied to the beam (My, P, Vy and Vz = 0), what is the normal stress at point F? Give your answer in kPa to two decimal places with negative indicating compression and positive indicating tension. b/4 М, h E Ihis F h/3 В M. D b/4
Determine the magnitude of the vertical force Cy for the cantilever beam, where P = 29 kips and M = 40 kip-ft. A 3.5 ft O 21 kips O 25 kips 42 kips 18 kips 29 kips M B 6.5 ft
Determine the combined loadings and draw them on a volume element: (a)Section A-A, Point A on the cross section (b)Section B-B, Point B on the cross section
Two equal and opposite couples of magnitude M = 23 kN•m are applied to the channel-shaped beam AB. The cross-section is shown, with the length of CD as L = 133 mm. Determine the maximum compressive stress in the cross-section. (The result is accurate to one decimal place, in the unit of MPa. Please write down only the absolute value of the final result) M A M' B 180 mm L E D -36 mm 30 mm 30 mm