2) A rigid beam AB rests on the two short posts as shown. Post AC is made from steeland has a diameter of 20 mm. Post BD is made from aluminum and has a diameterof 40 mm. Assume E = 200 GPa for steel and E = 70 GPa for aluminum. Determinethe displacement (mm) of point F for a vertical load of 90 kN.A90 kN200 mmF-400 mmBD300 mm

Answered: Image /qna-images/answer/552671a8-3e24-4c4e-89a6-f81026ac3e05.jpg

Answered: 2) A rigid beam AB rests on the two…

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Similar questions

Problem 1: Slab design using the ACI moment coefficients Design the continuous slab shown using the ACI moment coefficients assuming the concrete weighs 24 kN/m3 and that a service live load of 15 kN/m is to be supported. The slabs are built integrally with the end supports, which are spandrel beams. fy= 420 MPa and f'c = 28 MPa. Draw a plan and section showing all reinforcements along the slab. E 7m - 6 m + 7m --
Q14 Find the load .if the load distance 3m and effort distance 10m and effort3D300N Effort Pivot Load
The rigid beam shown in is held by two vertical rods at A and C.If a 60 KN load is applied at B what is the displacement of this point (B) . Aluminum L- 3m A- 500 mm E- 70 GPa Steel L- 4 m A= 300 mm E- 200 GPa 3.5 m 2.5 m
A 0.5kg weight is hung from the end of a cantilever beam, causing a vertical displacement of y = -0.01 inches relative to no load. The weight is increased to 1.0kg. What is the new displacement relative to no load? Typed and correct answer please. I ll rate
The wing spar ABD of a light plane is made from 2014-T6 aluminum and has a cross- sectional area of 800 mm², a height of 79 mm, and a moment of inertia about its neutral axis of 1.07(106) mª. Assume A, B, and C' are pins. The neutral axis passes through the cross-section at half of its height. Connection is made along the central longitudinal axis of the spar. The anticipated loading is to be as shown. (Figure 1) Determine the absolute maximum bending stress in the spar. 0.6 m 14.4 kN/m 0.9 m B -1.8 m-
5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E-200 GPa and BD from aluminum with E-70 GPa. The diameters of posts AC and 80 are 25 mm and 40 mm, respectively. Determine the vertical displacement of point on AB 100 KN 400mm D 6. The timber beam has a cross-sectional area of 2000 mm and its modulus of elasticity is 12 GP Axial loads are applied at points B, C, and D as shown. Calculate the total change in length of the beam. Answer: 2.33 mm 40 KN 35 KN 20 KN 3.20 m 1.60m 3.20 m
Determine the maximum stress in a hollow column of Do = 160mm and Di = 100mm that supports a load of 40KN and a bending moment of 4KN-m.
A 2500 lbs point load is placed at 4 inches from support A. The beam is simply supported with a span of 16 inches. Determine the maximum flexural stress of the beam.
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.31 in2. Find the vertical displacement (in inches and absolute value) of point Coaused by the 2888-lb load if x = 8.7 ft and 8 = 46.5-. Use E = 29159 ksi for steel. Note: Round off the final answer to four decimal places. Rigid B P
Find the support reactions, draw the free-body diagram of the beams that shows the reactions and the equivalent loadings of the beams. Show the computation where P = 3 kN, M0 = 75 kN-m, w0 = 100 kN/m, a = b = c = 2.5 m, d = 1.75 m
Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 5 kips/ft, M = 220 kip-ft, L1 = 11 ft, L2 = 4 ft, and L3 = 6 ft. B C L1 L2 L3 O 49.6 kips O 41.9 kips O 81.8 kips O 58.8 kips 63.4 kips
A uniform light beam has length 6 m. The lefthand side rests on a roller and the right hand sideis welded horizontally to a support. It bears a uniform load of 2 kN/m downwards, a concentrateddownwards load of 3 kN at x = 2 m and a concentrated anticlockwise couple of 4 kN.m at x = 4 m.Determine the form of the beam.

SEE MORE QUESTIONS

Recommended textbooks for you

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS