The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their other ends are fixed. Lengths of AB and BC are 150 mm and 120 mm, T respectively. They have uniform cross- sections all over their lengths and the details of their cross sections are given on the figure. Here, ri =28 mm and r2 =45 mm. and both have a wall thickness of 4.2 mm. The ultimate shear strengths of the copper and aluminum are 150 MPa and 70 MPa, respectively. Determine the maximum value of torque, T in elastic limits. АВ BC

The copper shaft (G= 44 GPa) is bonded to A the aluminum shaft (G= 26 GPa) at B point and their other ends are fixed. Lengths of AB and BC are 150 mm and 120 mm, T respectively. They have uniform cross- sections all over their lengths and the details of their cross sections are given on the figure. Here, ri =28 mm and r2 =45 mm. and both have a wall thickness of 4.2 mm. The ultimate shear strengths of the copper and aluminum are 150 MPa and 70 MPa, respectively. Determine the maximum value of torque, T in elastic limits. АВ BC

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The true option
كشمذنس
In the figure, copper AB copper with a diameter of 24 mm and BC steel bars with a diameter of 20 mm are rigidly connected to each other at point B. A force of 6 kN was applied to the rod at the B point and 12 kN at the C point. Since the modulus of elasticity of copper is 100 GPa and the modulus of elasticity of steel is 200 GPa, find the displacement of the C point.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPa. Aluminum A = 400 mm2 Bronze A = 200 mm2 Steel A = 500 mm² P 2P 4P 2.5 m 2.0 m 1.5 m
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=33P=33 kipskips is applied to the assembly at A, two loads of Q=30Q=30 kipskips are applied at B, and two loads of R=35R=35 kipskips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 1717 ksiksi. The normal stress magnitude in steel rod (2) must be limited to 3030 ksiksi. The normal stress magnitude in brass rod (3) must be limited to 2121 ksiksi. Determine the minimum diameter required for each of the three rods.
In the system shown in the figure, 2 sheets are connected to each other with the help of rivets with equal diameters and are forced by the force F. Of the 16 rivet slots shown in the figure, only the rivets shown in the brackets were used, and holes were drilled only for the specified rivets (16 holes on the sheet are NOT available. Only A4, B1, C1, D3 are holes.) i) Determine the center of rotation of the rivets. ii) Determine the rivet diameter required for the system to be safe.
An aluminum tube of outer diameter R2 = 50 mm is heated such that it is mounted over a steel shaft of radius, R = 20 mm as shown in the figure The length I of the member is 3 m. MT R Ri If a G, = 77.2 GPa, G2 = 27 GPa, and torque of MT = 36 kN.m is applied to induce twisting in the member, Determine the maximum shear stress in shaft 1. 777
Figure 1 shows a composite shaft ABCD acted upon horizontal forces. The moduli of elasticity and the cross-section areas of the segments of the shaft are also provided. Eal 70 GPa E = 126 GPa E = 200 GPa AAR=58 mm² ABC 77 mm2 Acp = 39 mm² Сopper 20KN 8 kN Aluminum Steel 7 kN B 20KN A 8 kN 450 mm -300 mm -- 400 mm Figure 1: Axially loaded composite shaft 2.1. Construct the diagram of internal normal forces for each cross-section of the (6) shaft (3) 2.2. Calculate the displacement of the point C with respect to the fixed-point A 2.3. If the shaft must have one uniform diameter determine the required minimum diameter of the shaft if the normal yield stress in the composite shaft must not (11) exceed 450 MPa with a factor of safety equal to 1.8.
Problem: I+12 For the given compound curve (see figure): a. Determine R, and R2. b. Determine T, and T2. c. Determine C, and C2. d. Determine L, and L2. e. If the stationing of PC is at 10 + 304.62 m, determine the stationing of PCC and PT. T+T2 РСС Pl, I = 12° I = 15° Pl2 L2 T, PC6 (Sta PC = 10 + 304.62) PT Long chord = 300m I = 15° R2 R1 'O2 I = 12° R,
I need the answer as soon as possible
1. The steel shaft carries the axial loads as shown in the figure below. Determine the change in overall length of the shaft caused by these loads given that P = 3100 Ib. The cross-sectional area for each segment is shown in the figure. Use E = 29 X 10° psi for steel. %3D A = 0.75 in.² ЗР A = 1.0 in.² A = 0.5 in.? 2P -P 4P e-3 ft- - 5 ft 4 ft→