The concrete sections of a certain superhighway are designed to have a length of 25.0 m. The sections are poured and cured at 10.0°C. What minimum spacing should the engineer leave between the sections to eliminate buckling if the concrete is to reach a temperature of 50.0°C?

The concrete sections of a certain superhighway are designed to have a length of 25.0 m. The sections are poured and cured at 10.0°C. What minimum spacing should the engineer leave between the sections to eliminate buckling if the concrete is to reach a temperature of 50.0°C?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

One mole of oxygen gas is at a pressure of 5.10 atm and a temperature of 30.0°C. (a) If the gas is heated at constant volume until the pressure triples, what is the final temperature? °C (b) If the gas is heated so that both the pressure and volume are doubled, what is the final temperature? °C Need Help? Read It
Assume a person has lungs that can hold V = 5.5 L of air (at 1 atm), and their body temperature is currently T = 35.5° C. a. How many moles of air does the average human have in their lungs when they breath in?
(a) A tank contains one mole of helium gas at a pressure of 6.35 atm and a temperature of 22.0°C. The tank (which has a fixed volume) is heated until the pressure inside triples. What is the final temperature of the gas? °C (b) A cylinder with a moveable piston contains one mole of helium, again at a pressure of 6.35 atm and a temperature of 22.0°C. Now, the cylinder is heated so that both the pressure inside and the volume of the cylinder double. What is the final temperature of the gas? °C
A high-pressure gas cylinder contains 70.0 L of toxic gas at a pressure of 2.10 x 107 N/m2 and a temperature of 14.0°C. Its valve leaks after the cylinder is dropped. The cylinder is cooled to dry Ice temperatures (-78.5°C), to reduce the leak rate and pressure so that it can be safely repaired. (a) What is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change? N/m² (b) What is the final pressure if one-tenth of the gas escapes? N/m² (c) To what temperature must the tank be cooled to reduce the pressure to 1.00 atm (assuming the gas does not change phase and that there is no leakage during cooling)? K Additional Materials
A high-pressure gas cylinder contains 50.13 L of toxic gas at a pressure of 1.40 × 10¹N/m² and a temperature of 25.0°C. Its value leaks after the cylinder is dropped. The cylinder is cooled to dry ice temperature (-78.5°C) to reduce the leak rate and pressure so that it can be safely repaired. (a) What is the final pressure in the tank, assuming a negligible amount of gas leaks while being cooled and that there is no phase change?
A cube of ice is taken from the freezer at -8.8°C and placed in a 104 g iron cup filled with 279 g of water. Both the water & the cup are at 23.9°C. Eventually the system reaches thermal equilibrium at 12.4°C. Determine Qcup, Qwater (for the water initially in the cup), Qice, & the mass of the ice.Qcup = Qwater = Qice = mice =
A 1 kg bar of copper is heated at atmo- spheric pressure of 1.013 x 105 N/m². If its temperature increases from 14°C to 54°C, find the work done by the copper. The linear expansion coefficient of copper is 1.7 x 10-5 (°C)¹, its density is 8920 kg/m³ and its specific heat is 387 J/kg. ° C. Answer in units of J. part 2 of 2 What quantity of thermal energy is trans- ferred to the copper in this process? The specific heat of copper is 387 J/kg.° C. Answer in units of J.
The gap width is 1.610 cm when the temperature is 30.0°C. Determine the gap width when the temperature is 205°C. (Use 11 ✕ 10−6 (°C)−1 for the average coefficient of linear expansion for steel. Give your answer to at least three decimal places.)
Oil enters the outer tube of an insulated concentric tube heat exchanger at a temperature of 500K and exits at a temperature of 400K. The mass flow rate of the oil is 5kg/s, and the oil has a specific heat of 1.91 kJ/kgK. Saturated liquid water at 100°C enters the inner tube and exits at 100°C with a quality of 0.2. Determine the mass flow rate of the water.
2.40 moles of an ideal gas is initially at 40.0 oC and 1.35 atm. a) What is its volume under these conditions?b) If it is then compressed to one third of its initial volume and its pressure increases to 2.0 atm, what, in Centigrade degrees, will be its temperature?
Homework 2: Problem 7: When builders were constructing a sidewalk they forgot to include an expansion joint between two of the segments, L = 1.7 m at To = 20° C. Assume the opposite ends of each segment are fixed and the linear expansion coefficient is α = 11.8 × 10-6 °C-1. Part (a) As the day heats to Tb the segments press against each other and begin to raise the junction a distance h forming a triangle. What is the height (in meters) at Tb=110° F? h = ______ m Part (b) What should the gap have been, in units of meters, to prevent them from touching? g = ______m
Brass 0.030 m 5.0 µm Brass has linear thermal expansion coefficient a = 19 × 10-6rC . The picture shows a design defect in an electrical assembly: if the screw expands enough to touch the surface on the left, a dangerous short circuit will occur. The picture shows the assembly at 15°C. What is the maximum tempe ure the assembly can tolerate? 46.9°C 32.6°C 23.7°C 27.4°C 19.3°C