The compound shaft is attached to a rigid wall at each end and is subjected to the torqueT = 10 kN.m applied at point B. For the bronze segment AB, the diameter is di = 79 mmand Gbr = 35 GPa. For the steel segment BC, the diameter is d2 = 44 mm andGt = 83 GPa. Given that a = 2.5 m and b = 1.8 m, what is the torque reaction TAdeveloped at end A?dzBronzeSteel

Answered: Image /qna-images/answer/fc9e36cc-a3d4-425c-bf82-aa1b5f48ca2b.jpg

The compound shaft is attached to a rigid wall at each end and is subjected to the torque T = 10 kN.m applied at point B. For the bronze segment AB, the diameter is d1 = 79 mm and Går = = 44 mm and = 35 GPa. For the steel segment BC, the diameter is d2 Gst = 83 GPa. Given that a = 2.5 m and b = 1.8 m, what is the torque reaction TA developed at end A? Bronze Steel

The compound shaft is attached to a rigid wall at each end and is subjected to the torque T = 10 kN.m applied at point B. For the bronze segment AB, the diameter is d1 = 79 mm and Går = = 44 mm and = 35 GPa. For the steel segment BC, the diameter is d2 Gst = 83 GPa. Given that a = 2.5 m and b = 1.8 m, what is the torque reaction TA developed at end A? Bronze Steel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A: To determine:The magnitude of maximum shear stress in the shaft()

Q: The solid shaft is fixed at A and free at D. It is subjected to three concentrated torques at B, C…

Q: A solid bar of circular cross section has a diameter of 40mm and length of 1300mm. G=80GPa and…

A: Given T = 340Nm. , d = 40mm = 0.04m.

Q: (A,) See the figure below. There are two torques applied at B and D. Segment CD is a tube, while AB…

A: In the given problem, the dimensions and Modulus of rigidity have been converted to feet. Radius,…

Q: The solid shaft (G=70 GPa) has a diameter of 40 mm. Calculate: a. The magnitude and direction of the…

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: 3.4-1 A stepped shaft ABC consisting of two solid circular segments is subjected to torques 7, and…

Q: A two-segment shaft is used to transmit power at constant speed through the pulleys shown in the…

Q: Please give a detailed explanation with a free body-diagram.

A: To provide a detailed explanation along with a free body diagram (FBD) for determining the reaction…

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: A solid shaft of circular cross section has a diameter of 15mm and is loaded by a torque of 130Nm at…

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

Q: A steel axle is made from tubes AB and CD and a solid section BC. It is supported on smooth bearings…

A: The polar moment of inertia of the hollow shaft is The polar moment of inertia of the solid shaft…

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: 04- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: A 0.5 m-long metal composite shaft AB consists of a steel rod (radius r=25 mm), the outer surface of…

A: Answer and explanation are given below.Explanation: Please let me know if there are any further…

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

Q: A solid shaft BC is fixed at the B end and subjected to torque T at the C end, as shown below. The…

Q: 2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The compound shaft is attached to a rigid wall at each end and is subjected to the torque
T = 10 kN.m applied at point B. For the bronze segment AB, the diameter is di = 79 mm
and Gbr = 35 GPa. For the steel segment BC, the diameter is d2 = 44 mm and
Gt = 83 GPa. Given that a = 2.5 m and b = 1.8 m, what is the torque reaction TA
developed at end A?
dz
Bronze
Steel

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

ON 01 Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T, = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm. (b) What is the maximum angle of twist, aand where does it occur? -635 mm- -635 mm- |A To В •D d,
The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure. The journal bearings A and B exert on the shaft only the y and z components of the 100 mm 250 mm 50 mm support reactions. Dětermine the equilibrium torque T at gear C. Using the "Maximum 75 mm 150 mm Distortion Energy Theory" with Jallowable the together 80 MPa, smallest calculate possible diameter of the shaft millimeter that will support the loading. to the nearest 100 mm F.= 15 kN
6-26. The loading on a control torque tube for an aileron of an airplane may be idealized by a uniformly varying torque Tx = kx in-lb/in, where k is a constant(see the figure). Determine the angle of twist of the free end. Assume IpG to be constant.
1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
A steel stepped shaft ABCD fixed at A is subjected to three torques at points B, C and D, with magnitudes T₁ = 40 kip-in, T₂ = 50 kip-in and Ts= 30 kip-in and directions as shown in Figure 1.1. The segments AB and BC are solid with diameters dx = 3 in and dec = 2 in respectively, while segment CD is hollow with an outer diameter dan 1.5 in and a wall thickness of 0.25 in. The shear modulus of elasticity is equal to G=11.6x10³ ksl. T₁ T₂ 4 = 20 in A B L₂ = 20 in Figure 1.1 a) Draw the torsion moment diagram for the shaft and calculate how long should segment CD be so that the angle of twist between points B and D is equal to zero. T₁ 4₂-25 in b) If Ts is dropped, a fixed support is added at point D (as shown in Figure 1.2) and the length of segment CD is equal to 15 in, find the support reactions at points A and D and the maximum shear stress developed in segment BC. The magnitudes of the torques at points B and Care the same as in part a). B C L₂= 25 in T₂ * Figure 1.2 Hollow C Hollow…
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
Problem 3
A turbine rotor is mounted on a stepped shaft that is fixed at both ends as shown in The torsional stiffnesses of the two segments of the shaft are given by ka = 3,000 N-m/rad and k2 = 4,000 N-m/rad. The turbine generates a harmonic torque given by M(t) = Mo cos wt about the shaft axis with M, = 200 N-m and w = 500 rads. The mass moment of inertia of the rotor about the shaft axis is Jo = 0.05 kg-m. Assuming the equivalent torsional damping constant of the system as c, = 2.5 N-m-s/rad, determine the steady-state response of the rotor, 6(1). O(1) ke M(1) = M, cos ot Turbine rotor, Jo
Torsional T is applied to the hollow axis (G=80 GPa). Ewha Womans University, the maximum shear strain is γmax = 640 × 10-6rad Igo, inside andThe outside diameters are 120mm and 150mm, respectively.a. What is the maximum axial strain?b. Maximum axial stress?c. What is the maximum torque (T) meeting the above conditions?
Formulate the equation of angle of twist at end C with respect to A in terms of T
Gear shaft ABCDE is subjected to the torques shown in the figure. Find the internal torque in each seg- ment, and then plot the torsional moment diagram. Assume that the spacing between gears is constant, i.e., 10 in. T1 = T2 = 1000 lb-in. 500 lb-in. A B T3 = 800 Ib-in. C Ta = 500 lb-in. d = 1.0 in. D T; = 800 lb-in. E