The compound shaft in Figure is attached to rigid supports. For Bronze G = 40 GPa and for Aluminum G = 35 MPa. Find the max shearing stress in each material, the rotation at B T-30KN.m/m 200 mm Auminem Bronze 100 B 3 m 2 m

The compound shaft in Figure is attached to rigid supports. For Bronze G = 40 GPa and for Aluminum G = 35 MPa. Find the max shearing stress in each material, the rotation at B T-30KN.m/m 200 mm Auminem Bronze 100 B 3 m 2 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hand written please.
It is made of solid circular cross-section bars, whose geometry and loading condition are given in Figure 2. The system formed is made of steel material and the torsional moments is under the influence. The diameter of the AB part of the rod is 100 mm; The diameter of the BC part is 60 mm. the shear modulus of steel is G = 80000 MPa. a)Draw the torsional moment diagram of the rod. b)Calculate the maximum shear stress that will develop in the system. c)Calculate the relative rotation value of point C with respect to point A b. M2 (kN.m) M1 (kN.m) B. A 100 mm 60 mm C а-а b-b L3 (mm) L4 (mm) kesiti kesiti Şekil 2 M1 (kN.m) M2 (kN.m) L3 (mm) L4 (mm) 60 50 600 700
2. The assembly in Figure consists of a light rigid bar AB, pinned at 0, that is attached to the steel and aluminum rods. In the position shown, bar AB is horizontal and there is a gap, A = 5 mm, between the lower end of the steel rod and its pin support at C. Compute the stress in the aluminum rod when the lower end of the steel rod is attached to its support. 0.75 m 1.5 m A B Steel A = 250 mm? E = 200 GPa Aluminum L= 2 m A = 300 mm? E = 70 GPa D
An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 30 mm as shown in the figure. The length I of member is 3 m. MT R Ri If a G, = 77.2 GPa G, = 27 GPa and torque of M- = 76 kN. m S appirec o rdICE TWISting in the memper Determine the maximum shear stress in the tube
The nut on a bolt is tightened by applying a force of P = 18 lb to the end of a wrench at a distance of a = 7.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.425 in. What is the maximum torsional shear stress in the body of the bolt? Answer: Tmax i a psi
Situation 5 A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa. Solve for the total angular deformation. 800 N-m 1300 N-m 1200 N-m 2 m 1.5 m 3 m
QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is applied to the end B of the shaft. Determine the rotation of section B. The shaft and beam are made of an aluminium alloy for which E= 720 GPa and G = 27 GPa, Neglect the strain energy of the hub DF. IC 400 mm 200 mm- 40.0 mm D 60.0 mm 400 mm 800 mm HO H 30.0 mm T= 2.00 kN.m
Problem # 8: A bar made from aluminum (E = 72 GPa) has a diameter of 12 mm. When the bar is subjected to a tensile axial force P, its diameter is decreased by 0.018 mm. Assume the Poisson's ratio to be 0.33. Determine the value of loads P and its axial deformation. d = 12 mm P L 1.20 m P
SOLVE
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the allowable shear stress is 60 MPa, determine the largest torque that can be applied safely to the tube. (b) Compute the corresponding angle of twist. Use G = 80 GPa for steel. 90 mm 90 mm -90 mm --90 mm →
A 52-kip force acts on a machine part at point A as shown below. The diagram shows the internal normal force, shear force and bending moment acting on a particular RECTANGULAR Cross section. -30in N 10in 26in F=52 kip The value of the bending moment M you would use to find the bending stress on a stress element located 2 inches up from the bottom of the rectangular cross section is closest to: 264 kip-in O a. 408 kip-in Ob. 1,464 kip-in O c. 1,608 kip-in