The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges. The shaft is subjected to a torque of T = 1150 N m. The material is A-36 steel, G = 75 GPa. (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. VOAE¢ t vec Figure < 1 of 1 po/D= 0.115 rad Submit Previous Answers Request Answer T X Incorrect; Try Again; 5 attempts remaining 25 mm 75 mm 6 mm F150 mm. B < Return to Assignment Provide Feedback 225 mm, 150 mm

The composite shaft consists of a mid-section that includes the 25-mm-diameter solid shaft and a tube that is welded to the rigid flanges at A and B. Neglect the thickness of the flanges. The shaft is subjected to a torque of T = 1150 N m. The material is A-36 steel, G = 75 GPa. (Figure 1) Part A Determine the angle of twist of end C of the shaft relative to end D. Express your answer using three significant figures. VOAE¢ t vec Figure < 1 of 1 po/D= 0.115 rad Submit Previous Answers Request Answer T X Incorrect; Try Again; 5 attempts remaining 25 mm 75 mm 6 mm F150 mm. B < Return to Assignment Provide Feedback 225 mm, 150 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: For the solid circular rods exposed to the shown torques, determine the segment that experiences…

Q: as a diameter of 2 in. and a thickness of 0.20 in. Disk B is supplied with 15 hp of power of which A…

Q: A solid 40 mm diameter shaft is subjected to the torques shown. The bearings shown allow the shaft…

A: To determine:The magnitude of maximum shear stress in the shaft()

Q: The solid shaft is fixed at A and free at D. It is subjected to three concentrated torques at B, C…

Q: A thin-walled tube is subjected to torsion as shown. Determine the angle of twist produced. (in rad)

A: Given Radius =300 mm = 0.3 m Length = 6 m Thickness = 25 mm = 0.025 m T = 4kN m = 4000 Nm G = 70 GPa…

Q: The 66-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and…

Q: A motor drives a shaft at 300 rpm and a power output of 100 kW. The shaft is made of A-36 steel and…

Q: Torsion A hollow circular shaft has inside and outside diameters of 30 mm and 40 mm respectively.…

Q: If it is subjected to the triangular distributed load, determine the angle of twist of end A with…

A: Givenload intensity q=15 kNm/md=90mm=0.090mG=75 GPa

Q: A hollow circular steel shaft with an outside diameter of 2.569, and a wall thickness of 0.388 in.…

A: GivenPart 1D=2.569int=0.388inT=292 lb-ftL=124inG=12000 ksiPart 2D=2.915int=0.437inT=239 lb-ftL=105…

Q: The shaft is made of A-36 steel and has a diameter of 70 mm. It is fixed at B and the support at A…

Q: The torque of 250 kN.m produces a maximum shear stress of 48 MPa in the 8 m-long hollow steel shaft.…

Q: A hollow steel shaft with an outside diameter of 75 mm and a wall thickness of 5 mm is subjected to…

A: The given values are - do =75 mm, t=5 mm, T =4090×1000 Nmm, G =80×1000 Mpa, L=2000mm The inside…

Q: 40-mm-diameter The steel shaft is subjected to the torques shown. Determine the angle of twist of…

A: To Find : The angle of twist of the end. Given : The young modulus is G=75 GPa. Free Body Diagram :

Q: The device shown is used to mix soils in order to provide in-situ stabilization. The mixer is…

A: Givend=4in D=6inGst=11×103 ksi=11×106 psiTA=5000 ft lb=5000 ×12 in lb=60000 lb inTB=3000 ft lb…

Q: Hi, I need help with this question.

Q: Determine a.) the maximum torsional stress, τmax, and b.) the maximum angle of twist, φ, of the…

Q: The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure Part A If the allowable…

A: Givend=60mmτallow=80MPaθA/Callow=0.060 rad

Q: The torque of 100 kip - ft is applied in the 16-ft-long hollow steel shaft. Note that the inner…

Q: The 70-mm-diameter solid shaft shown is subjected to torques of 600 N·m and 1400 N·m at points B and…

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

Q: The A-36 steel shaft with a diameter of 30mm is supported on smooth bearings that allow it to rotate…

A: Given: The diameter of the shaft, d = 30 mm = 0.03 m The modulus of elasticity of the A36 shaft, G =…

Q: PROBLEM 1. The shafts are made of A-36 steel and both have 100 mm diameter. If a torque of 60 kN.m…

A: Given: Diameter of the shaft is 100 mm. For A-36 steel, G =75 Gpa. The applied torques are shown…

Q: Problem 10.2. A stepped steel shaft with diameters d, = 56 mm and d = 52 mm is twisted by torques T1…

A: d1 = 56 mm d2 = 52 mm T1 = 2.5 kN.m T2 = 1.5 kN.m

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

100%

Problem 5.90
5 of 5
The composite shaft consists of a mid-section that
includes the 25-mm-diameter solid shaft and a tube
that is welded to the rigid flanges at A and B. Neglect
the thickness of the flanges. The shaft is subjected to a
torque of T = 1150 N m. The material is A-36 steel,
G = 75 GPa. (Figure 1)
Part A
Determine the angle of twist of end C of the shaft relative to end D.
Express your answer using three significant figures.
Vo AZO vec
Figure
< 1 of 1
<>
p0/D =0.115
rad
Submit
Previous Answers Request Answer
T
25 mm
75 mm
X Incorrect; Try Again; 5 attempts remaining
T.
50 mm
225 mm
< Return to Assignment
Provide Feedback
150 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The A-36 steel assembly consists of a tube having an outer radius of 1 inch and a wall thickness of 0.125 inch. Using a rigid plate at B, it is connected to the solid 1-inch diameter shaft AB. Determine the rotation of the tube’s end C if a torque of 200lb inches is applied to the tube at this end. The end A of the shaft is fixed supported.
only HANDWRITTEN answer needed ( NOT TYPED)
The two shafts are made of steel (G=11x106 lb/in2). Each has a diameter of 1 in. , and they are supported by bearings at A, B and C, which allow free rotation. If the support at D is fixed, determine the angle of twist of end A when the torques are applied to the assembly as shown. Torque applied at H of 80 ft lbs, and at G of 40 ft lbs in opposing directions as seen in the figure
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the shaft and delivers 3 hp while rotating at 1800 rpm (revolutions per minute). Gears B, C, and D remove the powers indicated in the figure. Given the following two criteria, determine the required diameter of the shaft to the nearest 1/s in. (1) The maximum shear stress must not exceed Tallow = 9 ksi. (2) In order to prevent binding or interference in the attached machin- ery, the angle of twist of gear B with respect to gear D must not exceed 1°. 1.25 ft 1.0 ft 3 hp 1.5 ft 1 hp 0.5 hp 1.5 hp
A metal shaft ABCD with variable cross-section is subjected to three external torques (T₁=28 kip- in, T2=8 kip-in, and T3=10 kip-in) as shown in the figure below. Each torque is acting at the locations marked with circular points along the shaft. Note that a 16-inch long segment of the shaft at the free end (right) has a 1-inch diameter bore. The dimensions (lengths and diameters) of the shaft are given in the figure. Assume deformation is linear elastic and take G=12×106 psi. D [3" 16"- X C T₁ 2" -32"- T₂ 1" diam. bore B -16"- A T3 the bar has a uniform diameter d along its full length, but external torques remain the same and are applied at the same locations. If the failure shear stress for the material is equal to Tfail = 10 ksi, and the factor of safety is equal to 2, determine the required (uniform) diameter d for the bar. Assume that the bar is solid for its entire length.
A solid 0.64-in.-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 lb-ft 50 lb-ft 70 Ib-ft | (1) 30 lb-ft A (3) B D 3150 psi O 2524 psi 1876 psi O 2331 psi O 2932 psi
Problem 3
An aluminum shaft with a constant diameter of 50 mm is loaded by torques applied to gears attached to it as shown in the figure. Using G = 28 GPa, determine the relative angle of twist of gear D relative to gear A. Note: SHOW FBD AND DETAILED SOLUTION
The A36 steel shafts as shown in the figure below are made from two segments: solid segment AC with diameter = 1 in and a hollow segment CB with an outside diameter = 2 in and inside diameter = 1 in. The shaft is fixed at both ends. Determine the magnitude of the applied torque T (lb-in) if the reaction at A is 600 lb-in clockwise.
Formulate the equation of angle of twist at end C with respect to A in terms of T
The torques shown are applied to a 6 mm radius solid shaft with G = 70 GPa. Determine the maximum shear stress in the shaft and the rotation of end gear A with respect to fixed support E 40 Nm 280 Nm 05 m 150 N m 100 m 04 m (a)