The composite shaft, consisting of aluminum. copper. and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Also determine the displacement of B with respect toC A ANSWER in. B. ANSWER in Aluminum Copper Steel Eg = 10(10³) ksi AAB = 0.09 in? Ecu = 18(10') ksi ABC = 0.12 in? Eg = 29(10') ksi %3D %3D %3D AcD = = 0.06 in? %3D %3D 3.50 kip 1.75 kip 2.00 kip 1.50 kip A B 3.50 kip D 1.75 kip -18 in.- 12 in.- -16 in-

The composite shaft, consisting of aluminum. copper. and steel sections, is subjected to the loading shown. Determine the displacement of end A with respect to end D and the normal stress in each section. The cross-sectional area and modulus of elasticity for each section are shown in the figure. Neglect the size of the collars at B and C. Also determine the displacement of B with respect toC A ANSWER in. B. ANSWER in Aluminum Copper Steel Eg = 10(10³) ksi AAB = 0.09 in? Ecu = 18(10') ksi ABC = 0.12 in? Eg = 29(10') ksi %3D %3D %3D AcD = = 0.06 in? %3D %3D 3.50 kip 1.75 kip 2.00 kip 1.50 kip A B 3.50 kip D 1.75 kip -18 in.- 12 in.- -16 in-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a. A solid cireular shaft of length of 3 m and diameter of 50 mm rotates at 1200 rpm by a 400 HP electric motor at its middle. It derives two machines of 150 HP and 250 HP at left and right ends of the shaft, respectively. Determine the maximum shear stress and relative displacement of the two ends of the shaft. Take G = 85 GPa.
A hollow shaft with an outside diameter of 3.2 in. and an inside diameter of 2.6 in. is subjected to both a torque of T = 614 lb-ft and an axial tension load of P = 7410 lb, as shown. (a) Determine the principal stresses (σp1 > Op2) and the maximum shear stress Tmax at point H on the surface of the shaft. (b) Show the stresses of part (a) and their directions in an appropriate sketch. H (1) I X B
The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the handle as shown. The dimensions a and b are 110 mm and 220 mm respectively. If the diameter of the shaft is 24 mm, determine the maximum normal and shearing stress in the shaft. FLANGE a SHAFT HANDLE
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
echanics of Materials I X t.php Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d= 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. Yo Letferbimtse ENene 302 704 MPal
A1 m long and 35 mm diameter aluminum shaft is to be replaced by a steel hollow shaft of the same length and the same outside diameter. It is required to design the steel shaft to withstand double the shear stress that of aluminum shaft. Determine the inside diameter of the stee I shaft. Find the values of the shear stresses on each shaft if a torque of 3 kN.m is applied to both of d=20mm them.
3: T = 10.11 kN-m
Please help. This problem involves torsional stress and strain. Thank you.
A 4-m cantilever beam is loaded as shown. The cross section is formed with two concentric circles of radii 45 mm and 35 mm. If the allowable stress is 150 MPa, Ra 1 X 12 h Find the allowable maximum value of F. Select the correct response: 2.898 KN 2.269 KN 3.606 KN 4.392 KN < Previous Ri
4) The composite shaft consists of a solid brass segment (1) and a solid aluminum segment (2) that are connected at flange B and securely attached to rigid walls at A and C. Brass segment (1) has a diameter of 18 mm, a length of L₁ = 235 mm, and a shear modulus of 39 GPa. Aluminum segment (2) has a diameter of 24 mm, a length of L₂ = 165 mm, and a shear modulus of 28 GPa. If a concentrated torque of 270 Nm is applied to flange B, determine (a) the maximum shear stress magnitudes in segments (1) and (2). (b) the rotation angle of flange B relative to support A. N y A 235 mm (1) B 165 mm 270 N-m (2) C x
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1