The column is subjected to an axial force of 8 kN which is applied through the centroid of the cross-sectional area. Determine the average normal stress acting at section a-a. Show the free body diagram. 8kN 75m lo mm 75 mm 10 mm 10 mim -70 mm 70 mm a

Q: Air pressure in the cylinder is increased by exerting forces P = 2 kN on the two pistons, each…

A: Given Data: The outer radius of the cylinder is: rO=47 mm The force exerted on the walls is: P=2…

Q: The cross-sectional area of bar ABCD is 500 mm?. Determine the stress in segment BC. 40 kN 35 kN 20…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: The two rods support the vertical force of P = 40 kN. Determine the normal stress in rod AB and AC…

A:

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: The tine ABC of the fork lift is subjected to a uniform distributed loading as shown. If it is pin…

A:

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: The solid circular rod has a cross-sectional area of 420 mm². It is subjected to a uniform axial…

A:

Q: Determine the average normal stress developed in rod AB if the load has a mass of 50 kg.  The…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The solid bar has a diameter of 50 mm. The two forces and the torque Tx are acting at the origin of…

A:

Q: 1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow =…

A:

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: The 2-Mg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC,…

A: Given: The mass of the concrete pipe is m=2 Mg. The diameter of the cable AC is d’=10 mm=0.01 m.…

Q: The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial…

A:

Q: *8-44. Determine the normal stress developed at points A and B. Neglect the weight of the block.

A:

Q: The sign is supported by a hollow structural tube of 15 in. outer diameter and 0.5 in. wall…

A:

Q: If the load has a weight of 2940 N, determine the magnitude of the maximum compressive normal stress…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.